homebrew.357
Member

1244 Likes

Page 7 of 83 First 12345678910111213141516171819202157 ... Last

• Jump to page:

1. 
   mimms2 liked post by homebrew.357 On thread : Marlin 30-30 setup

   My 336 Marlin as the first "right " rifle for me, I`m left handed and had been using a right hand P/ H .308 bolt action for a bit so when I saw them at Reloaders for $400 I grabbed one. It was blued...

   Liked On: 24-05-2020, 11:01 PM

2. 
   dannyb liked post by homebrew.357 On thread : Marlin 30-30 setup

   My 336 Marlin as the first "right " rifle for me, I`m left handed and had been using a right hand P/ H .308 bolt action for a bit so when I saw them at Reloaders for $400 I grabbed one. It was blued...

   Liked On: 24-05-2020, 09:56 PM

3. 
   takbok liked post by homebrew.357 On thread : Making a Rolling block rifle on my lathe.

   Well you just make sure it`s all clamped up nice and tight, then just small cuts nice and slowly. They say in machining you make hast slowly and now you can see the transformation from round lump of...

   Liked On: 15-05-2020, 11:53 AM

4. 
   SixtyTen liked post by homebrew.357 On thread : Making a Rolling block rifle on my lathe.

   Well you just make sure it`s all clamped up nice and tight, then just small cuts nice and slowly. They say in machining you make hast slowly and now you can see the transformation from round lump of...

   Liked On: 15-05-2020, 09:59 AM

5. 
   canross liked post by homebrew.357 On thread : Making a Rolling block rifle on my lathe.

   Well you just make sure it`s all clamped up nice and tight, then just small cuts nice and slowly. They say in machining you make hast slowly and now you can see the transformation from round lump of...

   Liked On: 13-05-2020, 12:33 PM

6. 
   Micky Duck liked post by homebrew.357 On thread : Making a Rolling block rifle on my lathe.

   Well you just make sure it`s all clamped up nice and tight, then just small cuts nice and slowly. They say in machining you make hast slowly and now you can see the transformation from round lump of...

   Liked On: 11-05-2020, 07:28 PM

7. 
   canross liked post by homebrew.357 On thread : Making a Rolling block rifle on my lathe.

   Hi here`s a bigger pic of some clever bugger stuff, I forgot to mention it`s the saddle that's moved in .015" and clamped up, them the chuck`s turned on, cross slide is on infeed and cutter then...

   Liked On: 11-05-2020, 09:38 AM

8. 
   SixtyTen liked post by homebrew.357 On thread : Making a Rolling block rifle on my lathe.

   Hi here`s a bigger pic of some clever bugger stuff, I forgot to mention it`s the saddle that's moved in .015" and clamped up, them the chuck`s turned on, cross slide is on infeed and cutter then...

   Liked On: 10-05-2020, 12:12 AM

9. 
   Micky Duck liked post by homebrew.357 On thread : Making a Rolling block rifle on my lathe.

   Hi here`s a bigger pic of some clever bugger stuff, I forgot to mention it`s the saddle that's moved in .015" and clamped up, them the chuck`s turned on, cross slide is on infeed and cutter then...

   Liked On: 08-05-2020, 08:25 PM

10. 
    canross liked post by homebrew.357 On thread : Making a Rolling block rifle on my lathe.

    Had our first bit of hail a shower so getting nipper, had to stoke up the fire, so on with the gummies for a load of fire wood. So while I had them on fired up the lathe to fly cut the tang top. When...

    Liked On: 08-05-2020, 12:56 PM

11. 
    Joe_90 liked post by homebrew.357 On thread : Making a Rolling block rifle on my lathe.

    Now look here Micky you are going to stop watching Shortland street for a bit, and get your head around the mechanical bits, a can opener is for tins, not removing primers. Look at this, setup to cut...

    Liked On: 08-05-2020, 12:18 PM

12. 
    Scout liked post by homebrew.357 On thread : Making a Rolling block rifle on my lathe.

    AAaa, what did you say, 139003

    Liked On: 08-05-2020, 10:55 AM

13. 
    ishoot10s liked post by homebrew.357 On thread : Making a Rolling block rifle on my lathe.

    Now look here Micky you are going to stop watching Shortland street for a bit, and get your head around the mechanical bits, a can opener is for tins, not removing primers. Look at this, setup to cut...

    Liked On: 07-05-2020, 11:38 PM

14. 
    ishoot10s liked post by homebrew.357 On thread : Making a Rolling block rifle on my lathe.

    Had our first bit of hail a shower so getting nipper, had to stoke up the fire, so on with the gummies for a load of fire wood. So while I had them on fired up the lathe to fly cut the tang top. When...

    Liked On: 07-05-2020, 11:38 PM

15. 
    Micky Duck liked post by homebrew.357 On thread : Making a Rolling block rifle on my lathe.

    Got it, good lad, it`s clamped on the cross slide and it moves form left to right, in front of the chuck, move in 0.015" fly cutter spinning slowly and cross slide in feed and it slowly cuts off very...

    Liked On: 07-05-2020, 07:46 PM

Page 7 of 83 First 12345678910111213141516171819202157 ... Last

• Jump to page: