homebrew.357
Member

1244 Likes

Page 80 of 83 First ... 30666768697071727374757677787980818283 Last

• Jump to page:

1. 
   res liked post by homebrew.357 On thread : Making A Quigley Sharps Rifle on my lathe.

   But wait there`s more!, I also used car spring for the set triggers, they need to be hard as well, with lots of milling, grinding and polishing , made the set spring as well and a bit of a test ,all...

   Liked On: 12-07-2014, 02:21 AM

2. 
   Maca49 liked post by homebrew.357 On thread : Making A Quigley Sharps Rifle on my lathe.

   But wait there`s more!, I also used car spring for the set triggers, they need to be hard as well, with lots of milling, grinding and polishing , made the set spring as well and a bit of a test ,all...

   Liked On: 11-07-2014, 11:17 PM

3. 
   nevereadyfreddy liked post by homebrew.357 On thread : Making A Quigley Sharps Rifle on my lathe.

   But wait there`s more!, I also used car spring for the set triggers, they need to be hard as well, with lots of milling, grinding and polishing , made the set spring as well and a bit of a test ,all...

   Liked On: 11-07-2014, 08:52 PM

4. 
   Toby liked post by homebrew.357 On thread : Making A Quigley Sharps Rifle on my lathe.

   But wait there`s more!, I also used car spring for the set triggers, they need to be hard as well, with lots of milling, grinding and polishing , made the set spring as well and a bit of a test ,all...

   Liked On: 11-07-2014, 08:43 PM

5. 
   Scouser liked post by homebrew.357 On thread : Making A Quigley Sharps Rifle on my lathe.

   Hi, Hey Maca is your one a Shilo sharps, with a 1-18" twist, it will shoot out to 800/1,000, like Billy Dixson. I`m thinking of 1-20" or 1-"24, should be good to 3/400 yards and a lighter bullet?....

   Liked On: 11-07-2014, 09:16 AM

6. 
   Scouser liked post by homebrew.357 On thread : Making A Quigley Sharps Rifle on my lathe.

   Here`s the new gun drill and barrel to be. the large round bit of aisi 1045 steel is going to be the receiver with a hell of a lot of machining!, O for a milling machine or c n c, good things take...

   Liked On: 11-07-2014, 09:15 AM

7. 
   Scouser liked post by homebrew.357 On thread : Making A Quigley Sharps Rifle on my lathe.

   Ok, That lumpy bit part of the under lever/trigger garde , had to make it in two pieces and when both were ready I weald them together, then a lot of grinding, bending, sanding, polishing for a nice...

   Liked On: 11-07-2014, 09:15 AM

8. 
   Scouser liked post by homebrew.357 On thread : Making A Quigley Sharps Rifle on my lathe.

   26656 Some more pic`s to see if I can upload them, The lumpy bit at lower right is then of the breech under lever front bit, making it in tow bits, think I`v got it. homebrew.357.

   Liked On: 11-07-2014, 09:15 AM

9. 
   Scouser liked post by homebrew.357 On thread : Making A Quigley Sharps Rifle on my lathe.

   26642 Here is a pic of where the breech block, (not mine) fits in the receiver, and seeing that I`m making it I don`t think a standard stock would fit, would like to make one of black walnut. This...

   Liked On: 11-07-2014, 09:15 AM

10. 
    Scouser liked post by homebrew.357 On thread : Making A Quigley Sharps Rifle on my lathe.

    2656226563Hi All, been off line for a bit, my computer had a brain fart and gassed it`s self. So new laptop and learning to get it going and it would not let me on the forum, got it fixed. So with...

    Liked On: 11-07-2014, 09:11 AM

11. 
    Beaker liked post by homebrew.357 On thread : Making A Quigley Sharps Rifle on my lathe.

    Hi, Hey Maca is your one a Shilo sharps, with a 1-18" twist, it will shoot out to 800/1,000, like Billy Dixson. I`m thinking of 1-20" or 1-"24, should be good to 3/400 yards and a lighter bullet?....

    Liked On: 11-07-2014, 08:55 AM

12. 
    veitnamcam liked post by homebrew.357 On thread : Making A Quigley Sharps Rifle on my lathe.

    Hi, Hey Maca is your one a Shilo sharps, with a 1-18" twist, it will shoot out to 800/1,000, like Billy Dixson. I`m thinking of 1-20" or 1-"24, should be good to 3/400 yards and a lighter bullet?....

    Liked On: 11-07-2014, 07:47 AM

13. 
    ishoot10s liked post by homebrew.357 On thread : Making A Quigley Sharps Rifle on my lathe.

    Hi, Hey Maca is your one a Shilo sharps, with a 1-18" twist, it will shoot out to 800/1,000, like Billy Dixson. I`m thinking of 1-20" or 1-"24, should be good to 3/400 yards and a lighter bullet?....

    Liked On: 10-07-2014, 10:54 PM

14. 
    ishoot10s liked post by homebrew.357 On thread : Making A Quigley Sharps Rifle on my lathe.

    Here`s the new gun drill and barrel to be. the large round bit of aisi 1045 steel is going to be the receiver with a hell of a lot of machining!, O for a milling machine or c n c, good things take...

    Liked On: 10-07-2014, 10:52 PM

15. 
    ishoot10s liked post by homebrew.357 On thread : Making A Quigley Sharps Rifle on my lathe.

    Ok, That lumpy bit part of the under lever/trigger garde , had to make it in two pieces and when both were ready I weald them together, then a lot of grinding, bending, sanding, polishing for a nice...

    Liked On: 10-07-2014, 10:51 PM

Page 80 of 83 First ... 30666768697071727374757677787980818283 Last

• Jump to page: