ishoot10s
Tread carefully in the suck...

758 Likes

Page 2 of 51 First 12345678910111213141516 ... Last

• Jump to page:

1. 
   ishoot10s liked post by Fssprecision On thread : Bsa sportsman 5 firing pin

   I made a few a while back and have some spare, $35 plus postage if ya want one. I have dealers license so can ship to a dealer near you without the need for Police mail order form.....PM me if...

   Liked On: 27-07-2023, 01:25 PM

2. 
   ishoot10s liked post by Fssprecision On thread : Adjusting Trigger Pull Blaser R93

   I am not familiar with the Blaser trigger as such (have not disassembled one) but if there is a coil spring in there I don’t see why you couldn’t change it for a stronger one. If you don’t know what...

   Liked On: 21-07-2023, 09:42 AM

3. 
   ishoot10s liked post by OPO On thread : Mini excavator centre pivot/swivel help

   O-rings have around 15% "crush" when installed. a little more on some static sealing arrangements. the o-ring groove will be something like 15-20% wider than the o-ring. almost certainly it'll be a...

   Liked On: 20-07-2023, 08:16 AM

4. 
   ishoot10s liked post by ZQLewis On thread : Mini excavator centre pivot/swivel help

   You can also assume that it will be imperial O-rings. They come in standard cross sections, 1.78mm 1/16" 3.5mm 1/8", 5.33 3/16", and 6.99mm 1/4", (Difference between metric and nominal Inch...

   Liked On: 20-07-2023, 08:16 AM

5. 
   ishoot10s liked post by NO4 On thread : Mini excavator centre pivot/swivel help

   I deal with hydraulic rams, rotators, motors and pumps everyday. Orings are measured from there ID with sections of 1/16(1.78mm), 3/32(2.62mm), 1/8(3.53mm),3/16(5.33mm) and 1/4(6.99mm) you can get...

   Liked On: 18-07-2023, 10:08 PM

6. 
   ishoot10s liked post by No good names left On thread : Mini excavator centre pivot/swivel help

   What NO4 said....

   Liked On: 18-07-2023, 09:54 PM

7. 
   ishoot10s liked post by NO4 On thread : Mini excavator centre pivot/swivel help

   use a set of internal calipers to measure your groove diameter set to id then measure with Vernier's. remember to allow for draw as well 229244

   Liked On: 18-07-2023, 09:54 PM

8. 
   ishoot10s liked post by MSL On thread : Mini excavator centre pivot/swivel help

   Don’t think he knows the cross section, as the existing rings will no longer be true to original size. Sent from my iPhone using Tapatalk

   Liked On: 18-07-2023, 09:14 PM

9. 
   ishoot10s liked post by Southcity On thread : Bike Porn - Regardless of the motor, Show off your "two wheeled" beasties

   Added to my Honda portfolio!! 228863

   Liked On: 13-07-2023, 06:57 PM

10. 
    ishoot10s liked post by XR500 On thread : Firearms Safety Authority

    The weakest link.... https://www.nzherald.co.nz/nz/revealed-nearly-30-police-staff-under-investigation-by-anti-corruption-unit/W4ITZLBX4JGL3CQQ7P7DYKZJNA/

    Liked On: 04-06-2023, 07:01 PM

11. 
    ishoot10s liked post by Huntn On thread : Boiling stags heads, why do some come out yellow and some white?

    I have worked out over the years that if the head is clean/fresh and only couple of days old it will always come out nice and white after boiling out. If the head is a week old and smelly or been...

    Liked On: 05-05-2023, 07:18 PM

12. 
    ishoot10s liked post by norsk On thread : show us your chainsaws

    Big tree, cold day, hot saw.

    Liked On: 03-04-2023, 07:57 AM

13. 
    ishoot10s liked post by Philipo On thread : Jakewire

    Owens memorial service was held in Oamaru Monday arvo, was a good turn out & caught up with a few of his mates. very surprised & disappointed that of the three bosses from the company he worked for...

    Liked On: 13-03-2023, 07:20 AM

14. 
    ishoot10s liked post by johnd On thread : What have I got here

    Cheers for that. The box has Best Bullets on a sticker and from serious shooters, but says 134 grain black whereas these are 124 grn and blue. So I didn't trust the label:thumbsup:

    Liked On: 02-03-2023, 07:33 PM

15. 
    ishoot10s liked post by whanahuia On thread : Hunting kazakhstan info

    Is Wazza 56 a member here? pretty sure hes done the Maral hunt. No Kazakstan, But my brother and I hunted Kyrgizstan some years back. Heres my experience and advice for that part of the world. ...

    Liked On: 23-01-2023, 07:53 AM

Page 2 of 51 First 12345678910111213141516 ... Last

• Jump to page: