ishoot10s
Tread carefully in the suck...

758 Likes

Page 28 of 51 First ... 1415161718192021222324252627282930313233343536373839404142 ... Last

• Jump to page:

1. 
   ishoot10s liked post by Bavarian_Hunter On thread : Blooding the Blaser R8

   Went out with my brother to blood his new R8 in 6.5x55mm on the weekend. Took out some dirty red dogs. 32130 32131 32132 32133

   Liked On: 15-12-2014, 03:28 PM

2. 
   ishoot10s liked post by homebrew.357 On thread : Making a Sharps Barrel in my lathe.

   Hi ishoot10s, No such luck mate, carn`t put the lathe in drive with the gear box locket up for cutting the octagonal , so yes I`m winding the saddle up and down, up and down, ext .ext,. Say one...

   Liked On: 10-12-2014, 08:10 PM

3. 
   ishoot10s liked post by homebrew.357 On thread : Making a Sharps Barrel in my lathe.

   Hi Guys, Now with a bit of work shop magic I have made my lathe an octagonal one, ( no tit pull Toby), made a ali disc to fit on my rifling register with eight holes for lock pin stop. The barrel is...

   Liked On: 10-12-2014, 06:34 PM

4. 
   ishoot10s liked post by jakewire On thread : Old BDL in New Clothes. Picture story.

   Figured I'd give this a go I bought this a long while ago now for a fair price I thought, bought rifle and rings, scope is mine Rifle made in 1990. 31838 31839 Shot quite well with factory ammo...

   Liked On: 07-12-2014, 07:40 AM

5. 
   ishoot10s liked post by homebrew.357 On thread : Making a Sharps Barrel in my lathe.

   Hi, Yep, just set up and have cut the chamber in my Sharps barrel, I used a t/c form cutter for the job with a 6/7 degree slope into the rifling throat and no lead for these old timers. I used a new...

   Liked On: 05-12-2014, 09:19 PM

6. 
   ishoot10s liked post by rs200nz On thread : NZSRA Bolt Action Match

   I've used that gun and stripper clips :) Well done Ray. Nice work. Would have loved to have been there with mine but just had too much on!.

   Liked On: 05-12-2014, 05:54 PM

7. 
   ishoot10s liked post by Dundee On thread : One Bullet Wander

   Headed into town with my hunting gear and a ferret tail that needed to be dropped into H&F for the http://www.huntingandfishing.co.nz/swamp-comp as PT wasn't here to enter the tail. I entered it for...

   Liked On: 29-11-2014, 09:28 PM

8. 
   ishoot10s liked post by 7mmsaum On thread : Question for the mechanically minded

   The silver series detriots 8v53, 8v72 and 8v96 ( fuel pincher) were supercharged and turbocharged Tomoana freezers has two V16 detroits as back up generator engines I used to service them when...

   Liked On: 27-11-2014, 10:06 PM

9. 
   ishoot10s liked post by HartHunter2 On thread : Blaser 6.5x55swed

   Hey guy I just baught a blaser 6.5x55 in an r8. I was wondering if anyone has had this set up before if so maybe a load for a120ttsx. Thanks

   Liked On: 27-11-2014, 06:48 AM

10. 
    ishoot10s liked post by lophortyx On thread : gamba

    it shouldn't be a problem.jim maniatis is an expert springmaker and should be able to make you one.google maniatis gunsmiths,and ring greg.if you can send broken spring or gun, you will soon have it...

    Liked On: 27-11-2014, 06:32 AM

11. 
    ishoot10s liked post by thenorwegian On thread : Hunter from Norway

    Hello! It's a Sako 85. caliber 9,3*62 Think that one was with a Norma Oryx 285 grain bullet Range about 220 meters Don't know how popular that bullet is in other countries. But it's really...

    Liked On: 25-11-2014, 06:25 PM

12. 
    ishoot10s liked post by thenorwegian On thread : Hunter from Norway

    Hello. 30 year old hunter from Norway. Hunt pretty much everything Norway have to offer. things like, grouse, moose, reindeer, deer, capercaillie. In Norway it's a big tradition to use dogs. ...

    Liked On: 24-11-2014, 09:38 PM

13. 
    ishoot10s liked post by homebrew.357 On thread : Making a Sharps Barrel in my lathe.

    So have set up for turning the O D to 1" at the muzzle and breech at 1.220" for 2" in from the end, this is for the tulip bit that has the receiver threads and then tapers down to 1.150". To set the...

    Liked On: 20-11-2014, 09:08 PM

14. 
    ishoot10s liked post by specweapon On thread : Forum Carbon Fibre Knife Bulk order

    So, good news everyone. The first lot of 20 knives has arrived today. I'll post a picture of them tomorrow and get them sent out Monday. Has only taken 3-4 weeks to arrive so hoping the next large...

    Liked On: 20-11-2014, 08:27 PM

15. 
    ishoot10s liked post by homebrew.357 On thread : Making a Sharps Barrel in my lathe.

    Got the bore out to .450" buy simply using a wooden dowel , cut a slot in one end and slot in a bit of 600 grt paper with a bit of thin plastic for backing, start at breech end, rod held with vice...

    Liked On: 18-11-2014, 10:07 PM

Page 28 of 51 First ... 1415161718192021222324252627282930313233343536373839404142 ... Last

• Jump to page: