janleroux
Member

186 Likes

Page 11 of 13 First 12345678910111213 Last

• Jump to page:

1. 
   Oli1102 liked post by janleroux On thread : Blow torch for annealing

   Oli1102 you are a step or so ahead of me, but that is on my todo list. As is I have annealed about 500 cases with this setup. Takes me about 10min to do 100 cases, so not too much drama. Use the...

   Liked On: 08-12-2019, 10:21 AM

2. 
   25 /08 IMP liked post by janleroux On thread : Blow torch for annealing

   Built one of these with parts off AliExpress. Costs about $50 and a couple of hours of assemble time. Used tempilaq (from Servotech in AKL) to get the correct heat level. ...

   Liked On: 08-12-2019, 10:00 AM

3. 
   Danco liked post by janleroux On thread : DIY suppressor anyone

   I have seen some posts on the Taranaki Long Range Shooters Facebook group some posts talking about 3D printed suppressors that Keith Blackie (Palmerston North) did. Sent from my iPhone using...

   Liked On: 09-10-2019, 05:44 AM

4. 
   Moa Hunter liked post by janleroux On thread : Buying a scope overseas while on holiday

   If you know what you would be looking for, apply for the import permit before you go. Otherwise you might need another holiday to get rid of the stress again... Sent from my iPhone using Tapatalk

   Liked On: 03-10-2019, 03:56 PM

5. 
   ebf liked post by janleroux On thread : Buying a scope overseas while on holiday

   If you know what you would be looking for, apply for the import permit before you go. Otherwise you might need another holiday to get rid of the stress again... Sent from my iPhone using Tapatalk

   Liked On: 03-10-2019, 02:55 PM

6. 
   Jaco Goosen liked post by janleroux On thread : Regulation to bring firearm/optics accessories or parts into the country

   I agree with Jaco - just get the permit. Simple to complete, and it saves a lot pain down the line. There was a detailed discussion a while ago - what Police says, what Customs says and what the...

   Liked On: 01-10-2019, 06:06 AM

7. 
   Terminator liked post by janleroux On thread : 6.5 Creedmoor

   Bought some 12mm steel plates on trademe a couple of months ago, so my shooting buddy and I decided to see how it will hold up against ELD-M 140’s and ELD-X 143’s at 200m. Short answer,...

   Liked On: 05-09-2019, 04:01 PM

8. 
   rewa liked post by janleroux On thread : 6.5 Creedmoor

   Bought some 12mm steel plates on trademe a couple of months ago, so my shooting buddy and I decided to see how it will hold up against ELD-M 140’s and ELD-X 143’s at 200m. Short answer,...

   Liked On: 26-08-2019, 10:59 AM

9. 
   Nick-D liked post by janleroux On thread : 6.5 Creedmoor

   Bought some 12mm steel plates on trademe a couple of months ago, so my shooting buddy and I decided to see how it will hold up against ELD-M 140’s and ELD-X 143’s at 200m. Short answer,...

   Liked On: 25-08-2019, 10:52 PM

10. 
    Steelisreal liked post by janleroux On thread : Best load for long range shooting?

    [QUOTE=Steelisreal;885042] Ahh mate - you are so describing what I am going through. Mine: Howa with a 24” in a GRS Bifrost stock. Also did a pillar and bedding job on it. Very happy with the...

    Liked On: 25-08-2019, 01:19 PM

11. 
    Sideshow liked post by janleroux On thread : Off target.

    I had similar results when trying to preload a bipod to much. So basically ending up pushing the rifle forward with my shoulder. Possibly try shooting without a bipod - just over a sturdy bag. ...

    Liked On: 26-07-2019, 08:26 AM

12. 
    rewa liked post by janleroux On thread : What's up with my scale.

    Also make sure your Wifi router and mobile phone is far away from where you work with your scale. Sent from my iPhone using Tapatalk

    Liked On: 19-07-2019, 09:10 PM

13. 
    xtightg liked post by janleroux On thread : What's up with my scale.

    Also make sure your Wifi router and mobile phone is far away from where you work with your scale. Sent from my iPhone using Tapatalk

    Liked On: 18-07-2019, 03:03 PM

14. 
    spada liked post by janleroux On thread : What's up with my scale.

    Also make sure your Wifi router and mobile phone is far away from where you work with your scale. Sent from my iPhone using Tapatalk

    Liked On: 18-07-2019, 09:59 AM

15. 
    Moa Hunter liked post by janleroux On thread : Using zero reset?

    My take on it: Zero stop should be that you can not dial back down below zero if you dialed up after compensating for a point of impact change over a long distance. Zero reset means that after...

    Liked On: 16-07-2019, 11:23 PM

Page 11 of 13 First 12345678910111213 Last

• Jump to page: