johnd
Member

1513 Likes

Page 85 of 101 First ... 357172737475767778798081828384858687888990919293949596979899 ... Last

• Jump to page:

1. 
   viper liked post by johnd On thread : Which model of the 10 /22 ?

   Back to the OP, I had the T model, awesome accuracy usually 1/2 inch at 50M, with win subs. Great trigger, but very forward heavy to shoot standing and not so flash as an all day carry gun. Sold it...

   Liked On: 04-08-2018, 06:28 PM

2. 
   Micky Duck liked post by johnd On thread : Dead wood on the tree of firearms evolution

   Re slotted screws ( and phirips for that matter or pozi) When god invented the square drive i was nearly converted.

   Liked On: 01-08-2018, 09:32 PM

3. 
   Steve123 liked post by johnd On thread : Dead wood on the tree of firearms evolution

   Re slotted screws ( and phirips for that matter or pozi) When god invented the square drive i was nearly converted.

   Liked On: 01-08-2018, 08:00 PM

4. 
   Steve123 liked post by johnd On thread : The largest stash of factory ammo you ever bought

   I got in on an NZ army surplus deal once. we had all put in a bid then rumour has it GC got the lot then that fell through so they went back to all the minimal bidders. 15c a round I got 2000 which...

   Liked On: 01-08-2018, 07:39 PM

5. 
   ebf liked post by johnd On thread : Chamber Reamers: Straight Neck or Tapered Neck

   Probably helped A LOT when dropping the cartridges into the chambers when facing that charging Rhino/ lion / elephant with trembling hand.:)

   Liked On: 29-07-2018, 09:06 PM

6. 
   rewa liked post by johnd On thread : Chamber Reamers: Straight Neck or Tapered Neck

   Probably helped A LOT when dropping the cartridges into the chambers when facing that charging Rhino/ lion / elephant with trembling hand.:)

   Liked On: 29-07-2018, 09:03 PM

7. 
   csmiffy liked post by johnd On thread : Recommended hunting projectiles for .357 mag

   124 /125 grain jacketed hollow points, roll them down the barrel fast

   Liked On: 26-07-2018, 07:41 PM

8. 
   Preacher liked post by johnd On thread : Processing animals

   Interested to know who does their own and who doesnt and for what reasons. Personally its a part of my ethos, for being responsible for that animal. but hey I may be different, i like the whole...

   Liked On: 23-07-2018, 11:11 PM

9. 
   Micky Duck liked post by johnd On thread : Little gongs

   So I got my son to blast out some wee gongs for 22 shooting..... just mild steel. i couldnt decide wether i wanted them to be diamonds or squares so we came up with this design. Hope i dont end up...

   Liked On: 23-07-2018, 08:34 PM

10. 
    Micky Duck liked post by johnd On thread : Sighting in a rifle on a short range

    This is for .222 Norma factory 50 grain sp They used to print it on the pkt FOR LINE OF SIGHT 1 1/2 INCHES ABOVE BORE 25 YDS 100YDS 200YDS 300YDS -.8" 0.0 ...

    Liked On: 20-07-2018, 08:50 PM

11. 
    Sarvo liked post by johnd On thread : Sighting in a rifle on a short range

    This is for .222 Norma factory 50 grain sp They used to print it on the pkt FOR LINE OF SIGHT 1 1/2 INCHES ABOVE BORE 25 YDS 100YDS 200YDS 300YDS -.8" 0.0 ...

    Liked On: 20-07-2018, 07:26 PM

12. 
    Steve123 liked post by johnd On thread : Freezing meat, advice for first visit

    I would plan to eat the meat you harvest before returning to Hawaii, we could have a forum barby in your honour.

    Liked On: 19-07-2018, 11:47 AM

13. 
    Pengy liked post by johnd On thread : Freezing meat, advice for first visit

    I would plan to eat the meat you harvest before returning to Hawaii, we could have a forum barby in your honour.

    Liked On: 18-07-2018, 11:03 PM

14. 
    10-Ring liked post by johnd On thread : Electronic scales

    I did an experiment with a run of loads, ( about 50 ) just threw them from the powder thrower. Out at 600 yds they all went 1/2 to 3/4 MOA. Some would have been effected by wind more than others....

    Liked On: 16-07-2018, 09:21 AM

15. 
    Steelisreal liked post by johnd On thread : 6.5 Creedmoor Loads for 1:8 Twist?

    Havent read it that I recall, its just an impression I have got. From reading different articles in other forums .... nothing concrete. One of the reasons that people wanted SP brass such as Lapua...

    Liked On: 13-07-2018, 11:46 PM

Page 85 of 101 First ... 357172737475767778798081828384858687888990919293949596979899 ... Last

• Jump to page: