johnd
Member

812 Likes

Page 1 of 55 12345678910111213141551 ... Last

• Jump to page:

1. 
   johnd liked post by Woody On thread : Cahill tells us where the criminals are getting guns.

   Cambell on tv1 was sickening to watch with luxon this morning. Switched off in under 30 seconds.

   Liked On: 25-03-2025, 11:47 PM

2. 
   johnd liked post by Gkp On thread : Nodes = waste of time.

   That type of test tells me the powder and projectile works for that rifle and is really only to find max preasure/velocity. Once you start seeing signs back off a wee bit and off you go

   Liked On: 04-03-2025, 12:29 PM

3. 
   johnd liked post by luv2safari On thread : Chukar Season Opens Saturday!

   I just had a resident covey of about 100 Valley Quail walk by my house, coming for a drink and raid on the dicki-bird feeders. The season closed two weeks ago. Our chukar were way down for several...

   Liked On: 02-03-2025, 08:31 PM

4. 
   johnd liked post by Trav-6mmrem On thread : Te Puke Rifle Club Long Range Hunters Shoot

   See you there john

   Liked On: 28-02-2025, 01:21 PM

5. 
   johnd liked post by Seventenths On thread : Diy case lube - isopropyl alcohol and lanolin

   I reload maybe a thousand rounds a year, sometimes less, sometimes more. After sizing, I run the cases through a stainless steel media tumbler which cleans inside and outside making the cases like...

   Liked On: 27-02-2025, 07:37 PM

6. 
   johnd liked post by Friwi On thread : Act submission points

   Just a couple of point I may add ( and I will in my submission): Regarding visitors licences, it used to take only 1 month for a visitor to get a licence, it now takes 4months, which refrain a lot...

   Liked On: 19-02-2025, 03:00 PM

7. 
   johnd liked post by Gunworks On thread : Robbie's Collection on Sale

   https://www.gunworks.co.nz/shop/category/second-hand--collectable-guns

   Liked On: 14-02-2025, 07:12 PM

8. 
   johnd liked post by Apocalypticaman On thread : Built my first handloading bench using recycled pallets

   Hi all, Built my first handloading bench today, using recycled (free) pallets I picked up, something I've wanted to do for a very long time. Bit tight on the budget so needed to find a way to do...

   Liked On: 06-02-2025, 07:41 PM

9. 
   johnd liked post by Tahr On thread : Sad Commentary on Life and Balance.

   Surely no one thinks that we don't have an illicit gun problem? And a gun crime problem? Don't get distracted by the numbers. They are just numbers. 17K? 10K? 5K? Whatever. There are too many guns in...

   Liked On: 07-01-2025, 12:39 PM

10. 
    johnd liked post by scotty On thread : first rangeday of 2025 for me

    ok so after my last day at the range i went home dejected , iwa sall over the place with my reloads (125gr sst and 170gr hornady bulldozers) so between then and now i did some soul searching and i...

    Liked On: 03-01-2025, 05:41 PM

11. 
    johnd liked post by Tentman On thread : Bruce Rifle Club?

    There are very very few people brave enough to put themselves out enough to take on the legal responsibilities of being a club offier operating a range. Unless you are prepared to become an officer...

    Liked On: 23-12-2024, 04:26 PM

12. 
    johnd liked post by buzzmann On thread : Tight cases after putting through the die

    Just screw die down a little bit called can over I think will fix problem or do way ray just said [emoji1685] Sent from my iPhone using Tapatalk

    Liked On: 11-12-2024, 01:49 PM

13. 
    johnd liked post by Shearer On thread : Culling brass

    For consistency sake, after 8 firings with a hot load I would bin the lot and start again from scratch.

    Liked On: 06-12-2024, 12:54 PM

14. 
    johnd liked post by Hahn On thread : Magnetospeed sporter faults

    I had an issue with my sporter staying powered up and then giving a bayo unplugged error. Apparently this is a common issue and the only advice given is to return it with people saying it's...

    Liked On: 13-11-2024, 08:55 PM

15. 
    johnd liked post by Micky Duck On thread : Another Trip to the Range

    I do it with motor oil too. Have not had powder sit long enough to be considered old. Any slight batch variation will be less by blending in old.not that I will notice anyway without chronograph and...

    Liked On: 22-10-2024, 07:26 AM

Page 1 of 55 12345678910111213141551 ... Last

• Jump to page: