keengunNic
Member

287 Likes

Page 17 of 20 First ... 34567891011121314151617181920 Last

• Jump to page:

1. 
   Micky Duck liked post by keengunNic On thread : 243 varmint projaectiles

   Ive got a couple hundred 75gr vmax sitting idle, theyd be perfect

   Liked On: 11-07-2021, 09:40 PM

2. 
   Pixie Z liked post by keengunNic On thread : Dinner thread?

   Day off today, so its wild pork belly burnt ends, smoked on the bbq for 2 hours at 120 Celsius, then into the cast iron pot for another hour with bbq sauce concoction and butter. 171198

   Liked On: 29-06-2021, 09:54 PM

3. 
   i41do2 liked post by keengunNic On thread : 7mm practical load test

   2227 is more temp stable, little less erratic, however ive found 2225 to be an excellent powder too. If i were you id stick with the 2217 considering the current component crisis, 2217 is a plenty...

   Liked On: 28-06-2021, 10:23 PM

4. 
   Beaker liked post by keengunNic On thread : Dinner thread?

   Stealing these recipes for sure man looks outstanding

   Liked On: 27-06-2021, 07:22 PM

5. 
   veitnamcam liked post by keengunNic On thread : Dinner thread?

   Day off today, so its wild pork belly burnt ends, smoked on the bbq for 2 hours at 120 Celsius, then into the cast iron pot for another hour with bbq sauce concoction and butter. 171198

   Liked On: 27-06-2021, 06:52 PM

6. 
   Beaker liked post by keengunNic On thread : Dinner thread?

   Day off today, so its wild pork belly burnt ends, smoked on the bbq for 2 hours at 120 Celsius, then into the cast iron pot for another hour with bbq sauce concoction and butter. 171198

   Liked On: 27-06-2021, 05:22 PM

7. 
   Mrs Beeman liked post by keengunNic On thread : Dinner thread?

   Day off today, so its wild pork belly burnt ends, smoked on the bbq for 2 hours at 120 Celsius, then into the cast iron pot for another hour with bbq sauce concoction and butter. 171198

   Liked On: 27-06-2021, 02:08 PM

8. 
   Three O'Three liked post by keengunNic On thread : federal vs adi bras

   Only once with federal brass, 300wsm, 168amax, rl17 cant particularly remember the amount of powder but it wasnt over stoked, not over pressure on the first firings, second firings was popping the...

   Liked On: 23-06-2021, 10:51 PM

9. 
   stagstalker liked post by keengunNic On thread : Superformance and rem mag

   Rl17 will work well with the 150 gr weight range. Never had any experience with heavier though sorry

   Liked On: 22-06-2021, 11:18 AM

10. 
    superdiver liked post by keengunNic On thread : 130ttsx powder options

    2208 will do the job in a 20" bbl perfectly

    Liked On: 18-06-2021, 07:30 AM

11. 
    Moa Hunter liked post by keengunNic On thread : Full length resizing 7mm Rem Mag problem

    Can you catch the sharp edge with your fingernail? If so id hazard a guess that your die has some form of manufacturing defect. Pull it apart give it a clean, send a scribe or anything pointy up the...

    Liked On: 16-06-2021, 12:38 PM

12. 
    Micky Duck liked post by keengunNic On thread : 110 vs 130gr TTSX

    I run the 120ttsx in 7mm08 bushpig, and to be honest, ill either sell my stock off or shoot them then switch over to a bog standard gameking. ( Just my personal and only experience with ttsx) 20"...

    Liked On: 12-06-2021, 12:57 PM

13. 
    Phil_H liked post by keengunNic On thread : 110 vs 130gr TTSX

    I run the 120ttsx in 7mm08 bushpig, and to be honest, ill either sell my stock off or shoot them then switch over to a bog standard gameking. ( Just my personal and only experience with ttsx) 20"...

    Liked On: 12-06-2021, 08:22 AM

14. 
    Smallfoot liked post by keengunNic On thread : Cleaning brass...

    I made a rotary wet tumbler as a prototype with random crap i had laying around, drawing up a proper frame now and going to make it out of aluminum at work. Stainless pins are the most expensive part

    Liked On: 12-05-2021, 05:21 PM

15. 
    mimms2 liked post by keengunNic On thread : Cleaning brass...

    I made a rotary wet tumbler as a prototype with random crap i had laying around, drawing up a proper frame now and going to make it out of aluminum at work. Stainless pins are the most expensive part

    Liked On: 12-05-2021, 04:04 PM

Page 17 of 20 First ... 34567891011121314151617181920 Last

• Jump to page: