Kiwi Sapper
Member

355 Likes

Page 14 of 24 First 123456789101112131415161718192021222324 Last

• Jump to page:

1. 
   Kiwi Sapper liked post by zimmer On thread : ORDER OF ACTIONS IN RE LOADING to be considered.

   I couldn't see anywhere where there was mention of wearing safety glasses particularly during priming or is that just a given and everyone does?

   Liked On: 01-06-2020, 11:00 PM

2. 
   Kiwi Sapper liked post by grandpamac On thread : ORDER OF ACTIONS IN RE LOADING to be considered.

   Greetings Kiwi Sapper, I think that you have 3 and 4 correct as a lot of the case stretching happens when full length resizing. Also agree that 5 should become 2 as you don't want cruddy cases in...

   Liked On: 01-06-2020, 03:00 PM

3. 
   Kiwi Sapper liked post by Cyclops On thread : ORDER OF ACTIONS IN RE LOADING to be considered.

   I full length resize (after waxing necks), then ultrasonic clean, dry usually on the same day. Sometime later I prime, load propellant, seat projectile generally on the same day. Sometime later I...

   Liked On: 01-06-2020, 02:49 PM

4. 
   Kiwi Sapper liked post by Oli1102 On thread : ORDER OF ACTIONS IN RE LOADING to be considered.

   This is my current process for rifle reloading. I do go a bit overboard but I only reload 50 or 100 at a batch so time spent isn’t much of an issue. I just added expand necks as I’m going to go down...

   Liked On: 01-06-2020, 02:45 PM

5. 
   Kiwi Sapper liked post by Dicko On thread : ORDER OF ACTIONS IN RE LOADING to be considered.

   The "right" sequence can vary depending on the equipment one uses. If your depriming as you FL size (i.e. useing the die), then annealing comes before as you don't want to be working hardened brass. ...

   Liked On: 01-06-2020, 02:40 PM

6. 
   Kiwi Sapper liked post by Cigar On thread : ORDER OF ACTIONS IN RE LOADING to be considered.

   Yes, 3 and 4 are correct order, fired cases that are within specs are often overlength after sizing. My step 1 (after inspecting cases) is tumbling, but I neck size with collet dies so no lube to...

   Liked On: 01-06-2020, 02:38 PM

7. 
   Kiwi Sapper liked post by DavidGunn On thread : ORDER OF ACTIONS IN RE LOADING to be considered.

   5.5 Check that correct primers are at hand.

   Liked On: 01-06-2020, 02:19 PM

8. 
   Kiwi Sapper liked post by matto1234 On thread : Succesful winter hunt with the mutt and girlfriend

   Took my girlfriend out for her first hunt in pureora yesterday, bit of rain here and there but overall not bad weather. Followed an old overgrown track for a couple ks which i had shot a pig on...

   Liked On: 31-05-2020, 06:06 PM

9. 
   Kiwi Sapper liked post by Ryan_Songhurst On thread : What in the world?

   Dents caused by pressure going up the ouside of the case after case head separated

   Liked On: 30-05-2020, 11:03 PM

10. 
    Kiwi Sapper liked post by Marty Henry On thread : Duh...............Stupid Boy just primed 60, 308 cartridges with Large Pistol Primers

    The one that needs a hammer. Seriously though they have softer cups to allow for whimpy pistol firing pins. They are likely to perforated and gas cut the bolt face. Knock them out and put them in...

    Liked On: 29-05-2020, 08:27 PM

11. 
    Kiwi Sapper liked post by Spitfire On thread : Duh...............Stupid Boy just primed 60, 308 cartridges with Large Pistol Primers

    At least you did prime them. I once filled 50 cases with powder before realising I hadn’t primed the cases.

    Liked On: 29-05-2020, 08:27 PM

12. 
    Kiwi Sapper liked post by NZ32 On thread : Duh...............Stupid Boy just primed 60, 308 cartridges with Large Pistol Primers

    Have done this before with 6.5CM, with after firing the pistol primer would have a hole in it from the firing pin pushing through.

    Liked On: 28-05-2020, 04:56 PM

13. 
    Kiwi Sapper liked post by Micky Duck On thread : Which is louder, a 12 or 410 bore.

    bird roofies....there is thread on it here somewhere....

    Liked On: 26-05-2020, 09:10 PM

14. 
    Kiwi Sapper liked post by ShepoCymro On thread : Let me introduce myself

    haha good one :) haha sorry sir. yeah it wasn't ment as a joke btw haha.

    Liked On: 26-05-2020, 11:05 AM

15. 
    Kiwi Sapper liked post by tiroahunta On thread : Which is louder, a 12 or 410 bore.

    Yeah bird shot ya gotta be pretty close. Be good to do it at nighttime n spotlight there roosting tree. Sent from my iPhone using Tapatalk

    Liked On: 25-05-2020, 11:33 AM

Page 14 of 24 First 123456789101112131415161718192021222324 Last

• Jump to page: