LBD
Member

165 Likes

Page 9 of 11 First 1234567891011 Last

• Jump to page:

1. 
   LBD liked post by Bill999 On thread : 6.5 Creedmoor advice

   Both are fantastic 6.5creed is a 308 case with the shoulder bumped back a little and necked down to 6.5 The creed and 308 are very efficient The bigger question is what bullet do you want to...

   Liked On: 05-04-2020, 12:26 PM

2. 
   LBD liked post by 10-Ring On thread : Need 6.5 Creedmore load for Tikka rifle

   I have a Tikka T3x and the throat is quite long and the magazine is M+ so you can seat the bullets well out. This drops the pressure so with my particular Tikka I can load in more powder and get...

   Liked On: 03-02-2020, 11:09 PM

3. 
   LBD liked post by DBL On thread : 7mm RM rechambering

   Hi Grimus, This is a great idea and I hope you pursue the project and post pictures of your progress. Do have a chat with Kiwi Greg as he has a 7mm 300NM reamer that could make your life easier....

   Liked On: 15-01-2020, 11:50 PM

4. 
   LBD liked post by Beaker On thread : Spooling Braid onto reels

   Just found this article, which seems to make good sense... https://activeanglingnz.com/2017/07/02/spooling-braid-properly/

   Liked On: 28-12-2019, 08:40 PM

5. 
   LBD liked post by The Claw On thread : Mil/Mil vs MOA/MOA

   I guess this is one point of view. I hold a very different opinion on FFP vs SFP and Mil vs MOA. All but 1 of my scopes are FFP Mil/Mil, the SFP MOA scope that I do have is a good scope (Leupold...

   Liked On: 03-09-2019, 03:08 PM

6. 
   LBD liked post by ishoot10s On thread : Unimpressed by Optima Can...

   First shots out of the R8 6.5x47 today. Started with the can on, quiet enough, but hardly a group, ugly as. Took it off and looked for strikes but couldn’t see any. Under good light though, noticed...

   Liked On: 02-06-2019, 10:26 PM

7. 
   LBD liked post by ebf On thread : Oh Bother!

   use a pick to rough up the inside of the remaining part of the case epoxy putty from the bottom end, then tap out from top with a drift once it has set. if that does not work, drill and tap the...

   Liked On: 02-06-2019, 02:04 PM

8. 
   LBD liked post by Beaker On thread : Fishing tomorrow!

   Mines a FC620HT. About 2200kg all up on the trailer. That's with 180L fuel and 2 chilli bins, on board toilet, and half a fishing tackle shop,.....

   Liked On: 25-05-2019, 07:14 PM

9. 
   LBD liked post by sometimes1 On thread : Gun Porn, show off your new toys

   Picked this up today Bergara BA13 take down in 44 magnum...

   Liked On: 08-05-2019, 02:34 PM

10. 
    LBD liked post by Friwi On thread : Gun of the week

    Hi , This week we have a Tikka in 223 into one of our chassis with a magnum over barrel suppressor. Stock and pistol grip were supplied by the customer. 110697 110698

    Liked On: 08-05-2019, 12:46 PM

11. 
    LBD liked post by Cigar On thread : 6.5mm questions....

    0.050 jump to the lands if loaded to mag length (may be slightly less, but at least 0.035)

    Liked On: 08-05-2019, 01:22 AM

12. 
    LBD liked post by Carlsen Highway On thread : Under the Mountain Light

    Under Mountain Light Wild Jim came down from the hill, came down bent and white, He had spent his life under southern mountain light No more creeks to cross on frozen morning, under a...

    Liked On: 05-05-2019, 09:34 PM

13. 
    LBD liked post by Oli1102 On thread : DIY Annealing

    I have pretty much finished building my DIY machine, based of Skips design on YouTube. It has cost me about $180 with almost $100 of that being the propane torch and hose. I initially planned on...

    Liked On: 05-05-2019, 05:00 PM

14. 
    LBD liked post by NZShoota On thread : Steel vs polymer AICS Mag question

    The genuine AI steel mags have a reinforcing plate spot welded inside the front of the mag which can be removed with a bit of effort. Gains a couple of mm. Just need to add a bit of plastic to extend...

    Liked On: 29-04-2019, 08:27 PM

15. 
    LBD liked post by spada On thread : Steel vs polymer AICS Mag question

    I went with steel Accurate mags .308 COAL 2.95 max MDT polymer are rated at COAL 2.80 from memory

    Liked On: 29-04-2019, 01:54 PM

Page 9 of 11 First 1234567891011 Last

• Jump to page: