m101a1
Member

376 Likes

Page 18 of 26 First ... 4567891011121314151617181920212223242526 Last

• Jump to page:

1. 
   Cordite liked post by m101a1 On thread : Moving the gun safe

   I f you can find studs drill a row of holes in the back 8mm more to top than base and screw in 70 -80 mm tec screws with screw gun or 18v drill cost under 20 for bit and 10 screws ,youll nether rip...

   Liked On: 29-07-2022, 02:44 PM

2. 
   CBH Australia liked post by m101a1 On thread : Moving the gun safe

   I f you can find studs drill a row of holes in the back 8mm more to top than base and screw in 70 -80 mm tec screws with screw gun or 18v drill cost under 20 for bit and 10 screws ,youll nether rip...

   Liked On: 29-07-2022, 12:58 PM

3. 
   Nasty Factory Trigger liked post by m101a1 On thread : Moving the gun safe

   I f you can find studs drill a row of holes in the back 8mm more to top than base and screw in 70 -80 mm tec screws with screw gun or 18v drill cost under 20 for bit and 10 screws ,youll nether rip...

   Liked On: 29-07-2022, 10:32 AM

4. 
   Mr300WSM liked post by m101a1 On thread : Moving the gun safe

   I f you can find studs drill a row of holes in the back 8mm more to top than base and screw in 70 -80 mm tec screws with screw gun or 18v drill cost under 20 for bit and 10 screws ,youll nether rip...

   Liked On: 28-07-2022, 11:52 PM

5. 
   XR500 liked post by m101a1 On thread : Moving the gun safe

   I f you can find studs drill a row of holes in the back 8mm more to top than base and screw in 70 -80 mm tec screws with screw gun or 18v drill cost under 20 for bit and 10 screws ,youll nether rip...

   Liked On: 28-07-2022, 11:38 PM

6. 
   bigbear liked post by m101a1 On thread : Moving the gun safe

   I f you can find studs drill a row of holes in the back 8mm more to top than base and screw in 70 -80 mm tec screws with screw gun or 18v drill cost under 20 for bit and 10 screws ,youll nether rip...

   Liked On: 28-07-2022, 10:58 PM

7. 
   XR500 liked post by m101a1 On thread : Interesting for Safari/Patrol owners, Cardan shaft brake warning.

   Bit like modern owner manuals say dont drink the battery contents . All landrovers are cardon shaft hand brakes and the old rule was , if in dought leave in 4wd and in gear .

   Liked On: 24-07-2022, 09:40 AM

8. 
   Longranger liked post by m101a1 On thread : Is my scope ruined

   Screw all the the way home tight and loosen the thin lock ring behind the power ring and unscrew the bell or ocular housing out till it suits . You have unscrewed the lense body not the focus ocular...

   Liked On: 18-07-2022, 03:21 PM

9. 
   No.3 liked post by m101a1 On thread : Is my scope ruined

   Screw all the the way home tight and loosen the thin lock ring behind the power ring and unscrew the bell or ocular housing out till it suits . You have unscrewed the lense body not the focus ocular...

   Liked On: 09-07-2022, 06:42 PM

10. 
    Moa Hunter liked post by m101a1 On thread : Baikal single shot rebarrel - Anyone done this?

    Why not make a clamp type front sight with a 15>20mm high blade that you can cut down to suit as there a lots of old peep sites floating around that could be fitted by the average bubba .

    Liked On: 26-06-2022, 03:42 PM

11. 
    XR500 liked post by m101a1 On thread : What reputable caliper manufacturers are out there?

    Got a kingchrome that shit so Im going to set at 125.1 mm and weld in position as a Paua measure

    Liked On: 26-06-2022, 12:07 PM

12. 
    yeah_na_missed liked post by m101a1 On thread : What reputable caliper manufacturers are out there?

    Got a kingchrome that shit so Im going to set at 125.1 mm and weld in position as a Paua measure

    Liked On: 21-06-2022, 11:24 PM

13. 
    Scouser liked post by m101a1 On thread : What reputable caliper manufacturers are out there?

    Got a kingchrome that shit so Im going to set at 125.1 mm and weld in position as a Paua measure

    Liked On: 21-06-2022, 10:14 PM

14. 
    Moa Hunter liked post by m101a1 On thread : What reputable caliper manufacturers are out there?

    Got a kingchrome that shit so Im going to set at 125.1 mm and weld in position as a Paua measure

    Liked On: 21-06-2022, 09:18 PM

15. 
    Micky Duck liked post by m101a1 On thread : What reputable caliper manufacturers are out there?

    Got a kingchrome that shit so Im going to set at 125.1 mm and weld in position as a Paua measure

    Liked On: 21-06-2022, 08:58 PM

Page 18 of 26 First ... 4567891011121314151617181920212223242526 Last

• Jump to page: