m101a1
Member

376 Likes

Page 24 of 26 First ... 1011121314151617181920212223242526 Last

• Jump to page:

1. 
   csmiffy liked post by m101a1 On thread : Martindale golok

   got golok 28 yrs ago when poisoning , shortined by 4ins and made a drop in sheaf for speed and was great on supple jack only mistake was rounding handle edges off so is harder to hold now with old...

   Liked On: 13-02-2021, 08:19 PM

2. 
   trapperjohn liked post by m101a1 On thread : How not to be invited again....

   Not getting over side to hold boat while you go get tractor and trailer in calm water beach launching .

   Liked On: 01-02-2021, 05:42 PM

3. 
   Got-ya liked post by m101a1 On thread : How not to be invited again....

   Not getting over side to hold boat while you go get tractor and trailer in calm water beach launching .

   Liked On: 01-02-2021, 01:45 PM

4. 
   Steve123 liked post by m101a1 On thread : How not to be invited again....

   Not getting over side to hold boat while you go get tractor and trailer in calm water beach launching .

   Liked On: 01-02-2021, 07:36 AM

5. 
   stingray liked post by m101a1 On thread : How not to be invited again....

   Not getting over side to hold boat while you go get tractor and trailer in calm water beach launching .

   Liked On: 31-01-2021, 09:52 PM

6. 
   Leonardo liked post by m101a1 On thread : Magazine rebuild for 303 Lee enfield action

   I did a version made out of a steel gen 1 ar10 mag by narrowing the front and tapering the follower to suit worked good for 4 rnds and that was ok the main thing was the follower angle was correct...

   Liked On: 12-12-2020, 12:14 AM

7. 
   Leonardo liked post by m101a1 On thread : Magazine rebuild for 303 Lee enfield action

   hi no pics of mag but just cut a strip out of front of mag with a 1mm cut off disc and ground to suit then squeezed together and mig welded /ground flat then cut follower to suit mag . lots of trial...

   Liked On: 12-12-2020, 12:14 AM

8. 
   jord liked post by m101a1 On thread : Shooting bag filler

   Cheap rice

   Liked On: 31-10-2020, 11:00 AM

9. 
   mikee liked post by m101a1 On thread : Shooting bag filler

   Cheap rice

   Liked On: 30-10-2020, 09:51 PM

10. 
    bumblefoot liked post by m101a1 On thread : Shooting bag filler

    Cheap rice

    Liked On: 30-10-2020, 09:10 PM

11. 
    Fat ninja liked post by m101a1 On thread : Quad bikes

    fuck polaris rip of parts go well but you pay and no after market parts go honda or yamaha if not to steep 400 /450 ok the 500 and up are wider and longer so can be hard to trailer or put on ute ....

    Liked On: 21-10-2020, 08:52 PM

12. 
    Moa Hunter liked post by m101a1 On thread : Smoking eel

    Ya probly right but the last time I did it was over 30yrs ago with a maori mate who showed me the trick . Now I have a soft spot for eels and prefer to just feed them .

    Liked On: 06-09-2020, 05:58 PM

13. 
    Max Headroom liked post by m101a1 On thread : Howa 1500 mag release mod.

    I used a ar finger stop from a rail on mine just about identical look but no flex

    Liked On: 04-08-2020, 07:47 PM

14. 
    veitnamcam liked post by m101a1 On thread : Realistically how far can i push my 12.5 inch 308

    have a look at the hornady ftx projs .I used to load up 160s for a mate running a 308 no 4 so loaded down to about 2500max fps but way faster than a 30/30 , they were devastating at all ranges out to...

    Liked On: 16-06-2020, 07:50 PM

15. 
    Dago liked post by m101a1 On thread : Which aperture for a lee enfield No4 mk2

    Fill 600 hole with solder or weld and re drill hole lower for 100 zero

    Liked On: 07-06-2020, 07:04 PM

Page 24 of 26 First ... 1011121314151617181920212223242526 Last

• Jump to page: