makka
Member

459 Likes

Page 3 of 31 First 1234567891011121314151617 ... Last

• Jump to page:

1. 
   gassedupbeans liked post by makka On thread : 5.6x57 single shot project

   Next step was to mill a slot for the extractor and test fit it. 251216 That was all good so milled the old extractor off and tig'd this one in place. Also drilled and tapped the shotgun barrel...

   Liked On: 10-03-2025, 11:07 AM

2. 
   ANTSMAN liked post by makka On thread : 5.6x57 single shot project

   More sanding and some water to raise the grain 269836 269837

   Liked On: 09-03-2025, 09:44 AM

3. 
   Micky Duck liked post by makka On thread : 5.6x57 single shot project

   More sanding and some water to raise the grain 269836 269837

   Liked On: 03-03-2025, 04:39 PM

4. 
   Deanohit liked post by makka On thread : 5.6x57 single shot project

   More sanding and some water to raise the grain 269836 269837

   Liked On: 02-03-2025, 09:48 PM

5. 
   Micky Duck liked post by makka On thread : Act submission points

   Thanks for all the posts in here, they certainly helped me to cover some of the points I wanted to but couldn't quite figure out how to articulate.

   Liked On: 27-02-2025, 09:29 AM

6. 
   Micky Duck liked post by makka On thread : 5.6x57 single shot project

   Looks good! Maybe I could just make a monoblock instead of finding old barrels to stub. A bit more progress, I glued on and shaped the ebony grip cap, just need to round it over now. 269545...

   Liked On: 27-02-2025, 08:57 AM

7. 
   RabbitStu liked post by makka On thread : 5.6x57 single shot project

   Looks good! Maybe I could just make a monoblock instead of finding old barrels to stub. A bit more progress, I glued on and shaped the ebony grip cap, just need to round it over now. 269545...

   Liked On: 27-02-2025, 08:46 AM

8. 
   6x47 liked post by makka On thread : 5.6x57 single shot project

   Looks good! Maybe I could just make a monoblock instead of finding old barrels to stub. A bit more progress, I glued on and shaped the ebony grip cap, just need to round it over now. 269545...

   Liked On: 27-02-2025, 08:26 AM

9. 
   STC liked post by makka On thread : Act submission points

   Thanks for all the posts in here, they certainly helped me to cover some of the points I wanted to but couldn't quite figure out how to articulate.

   Liked On: 27-02-2025, 07:38 AM

10. 
    Deanohit liked post by makka On thread : 5.6x57 single shot project

    Looks good! Maybe I could just make a monoblock instead of finding old barrels to stub. A bit more progress, I glued on and shaped the ebony grip cap, just need to round it over now. 269545...

    Liked On: 27-02-2025, 06:17 AM

11. 
    Hermitage liked post by makka On thread : Norinco model 4 early JW15

    Looks good mate, what cold blue did you use?

    Liked On: 23-02-2025, 02:47 PM

12. 
    Deanohit liked post by makka On thread : 5.6x57 single shot project

    More slow progress, had to hand fit the recoil pad as the belt broke on the sander almost straight away. I could have waited till I got a new belt but spare time is limited! 269237

    Liked On: 22-02-2025, 06:41 PM

13. 
    short swede liked post by makka On thread : 5.6x57 single shot project

    More slow progress, had to hand fit the recoil pad as the belt broke on the sander almost straight away. I could have waited till I got a new belt but spare time is limited! 269237

    Liked On: 22-02-2025, 03:58 PM

14. 
    Micky Duck liked post by makka On thread : 5.6x57 single shot project

    More slow progress, had to hand fit the recoil pad as the belt broke on the sander almost straight away. I could have waited till I got a new belt but spare time is limited! 269237

    Liked On: 22-02-2025, 07:44 AM

15. 
    Micky Duck liked post by makka On thread : 5.6x57 single shot project

    Cheers mate, I'm not half as skilled as quite a few of the guys on here. A mate did the machining of the barrel for me too, I might have been able to do it myself but in twice the time and probably...

    Liked On: 22-02-2025, 07:44 AM

Page 3 of 31 First 1234567891011121314151617 ... Last

• Jump to page: