Makros
Member

1197 Likes

Page 1 of 80 12345678910111213141551 ... Last

• Jump to page:

1. 
   rugerman liked post by Makros On thread : Quick change tool post, advice please

   Can send you the used one to keep it you want. Give me a PM.

   Liked On: Yesterday, 03:12 PM

2. 
   40mm liked post by Makros On thread : Quick change tool post, advice please

   Certainly looks like it to me.

   Liked On: 24-03-2025, 10:16 PM

3. 
   40mm liked post by Makros On thread : Quick change tool post, advice please

   Aliexpress if you are particular with which supplier is basically the same quality stuff we buy here from Machinery House etc. anyway. I might grab a few of those.

   Liked On: 24-03-2025, 03:30 PM

4. 
   40mm liked post by Makros On thread : Quick change tool post, advice please

   Can send you the used one to keep it you want. Give me a PM.

   Liked On: 24-03-2025, 11:27 AM

5. 
   40mm liked post by Makros On thread : Quick change tool post, advice please

   Yep worked out it was cheaper than buying the equivalent number of tool holders at the time.

   Liked On: 23-03-2025, 11:13 PM

6. 
   Fssprecision liked post by Makros On thread : Quick change tool post, advice please

   I've got two spares of these. One used and one unused: https://www.machineryhouse.co.nz/l292 Use one on my lathe. 271146 271147 271148 271149

   Liked On: 23-03-2025, 04:49 PM

7. 
   40mm liked post by Makros On thread : Quick change tool post, advice please

   I've got two spares of these. One used and one unused: https://www.machineryhouse.co.nz/l292 Use one on my lathe. 271146 271147 271148 271149

   Liked On: 23-03-2025, 04:39 PM

8. 
   samc liked post by Makros On thread : Winchester 88 Restoration

   Well spring comes around in about a month so the winter project better finish up. Restored a 1961 Winchester Model 88 .243. Before. Stock was quite banged up, action was rough, trigger felt like...

   Liked On: 20-03-2025, 10:28 PM

9. 
   GW001 liked post by Makros On thread : Toz 17 worthwhile seeking parts?

   Neither, doesn't stop them shooting fantastically though. I've got one I chopped to 16" and threaded for a suppressor. The bore was definitely not concentric, but that's what dial indicators and four...

   Liked On: 02-03-2025, 07:48 PM

10. 
    kristopher liked post by Makros On thread : Toz 17 worthwhile seeking parts?

    Neither, doesn't stop them shooting fantastically though. I've got one I chopped to 16" and threaded for a suppressor. The bore was definitely not concentric, but that's what dial indicators and four...

    Liked On: 02-03-2025, 03:53 PM

11. 
    SPEARONZ liked post by Makros On thread : Cleaning Rods

    I'll make a tongue in cheek comment that might get the popcorn flowing. Those that are worried about a cleaning rod touching the bore are either cleaning way too much, or would be horrified to know...

    Liked On: 01-03-2025, 05:00 PM

12. 
    BRADS liked post by Makros On thread : Cleaning Rods

    I'll make a tongue in cheek comment that might get the popcorn flowing. Those that are worried about a cleaning rod touching the bore are either cleaning way too much, or would be horrified to know...

    Liked On: 26-02-2025, 08:31 PM

13. 
    Waimohunts liked post by Makros On thread : Cleaning Rods

    I would recommend a one piece carbon fibre cleaning rod. Almost impossible to break and they'll never get bent. For that suite of calibres I'd go with two; a .22 cleaning rod, and a .27+ cleaning...

    Liked On: 25-02-2025, 01:10 PM

14. 
    zimmer liked post by Makros On thread : Cleaning Rods

    I would recommend a one piece carbon fibre cleaning rod. Almost impossible to break and they'll never get bent. For that suite of calibres I'd go with two; a .22 cleaning rod, and a .27+ cleaning...

    Liked On: 25-02-2025, 01:00 PM

15. 
    veitnamcam liked post by Makros On thread : 223 on deer

    69gn Targex. 130m hind quartering slightly away, entry via onside crease, through major vessels of the heart, out via the offside should joint. Offside lung was jelly, hear wasn't attached to...

    Liked On: 18-02-2025, 02:45 PM

Page 1 of 80 12345678910111213141551 ... Last

• Jump to page: