mark kiwi
Member

31 Likes

Page 2 of 3 First 123 Last

• Jump to page:

1. 
   mark kiwi liked post by Micky Duck On thread : New gun, New land, And a thankyou to the forum :)

   you SHOULD be able to sight in without firing a shot...well good enough to get you on the paper anyway...dead easy with break open like that....open action and place in something form enough that it...

   Liked On: 08-01-2021, 07:59 PM

2. 
   mark kiwi liked post by jono7 On thread : New gun, New land, And a thankyou to the forum :)

   Nice :cool:

   Liked On: 08-01-2021, 12:59 PM

3. 
   mark kiwi liked post by dogmatix On thread : New gun, New land, And a thankyou to the forum :)

   Good stuff. The forum has some good buggers on it.

   Liked On: 08-01-2021, 12:58 PM

4. 
   mark kiwi liked post by mucko On thread : Kiwiana Gongs!

   the ones i sell are biz400 or harder my 400 rounds are 3/4" thick

   Liked On: 08-10-2020, 10:15 AM

5. 
   mark kiwi liked post by JaSa On thread : Kiwiana Gongs!

   No cracks or splits, they are flat with a cut down one welded over the hole in the middle. Don't give a clear "ping" as sandwiched together but still okay to hear from 800m. Got 12 pieces for a box...

   Liked On: 08-10-2020, 10:14 AM

6. 
   mark kiwi liked post by JaSa On thread : Kiwiana Gongs!

   Need to be two welded together. Have a single one at 700m and the 6.5CM makes massive dents in it - even have a 143gr ELD-X stuck in it....

   Liked On: 07-10-2020, 08:54 AM

7. 
   mark kiwi liked post by r87mm On thread : Kiwiana Gongs!

   Ar400 min ,ar500 better. Used cutting edges off loaders and earth moving equipment including digger teeth work well. Other than teeth we often used old edges for wear areas on other plant so often...

   Liked On: 03-10-2020, 12:43 PM

8. 
   mark kiwi liked post by MSL On thread : Kiwiana Gongs!

   Both of those would likely fracture after a few centre fire rounds. I have a few ar500 gongs but also a couple of old wear plates off a brick forming machine which work well. Sent from my...

   Liked On: 03-10-2020, 12:43 PM

9. 
   mark kiwi liked post by 300CALMAN On thread : HELLO :-)

   Post more! Then you can post pics.. .50 ain't afraid of the wind.

   Liked On: 03-10-2020, 09:18 AM

10. 
    mark kiwi liked post by Wingman On thread : Remington 700 Bullpup chassis build

    Ive been favouring my Grendel and .223 AI lately so the Creedmore pup has been neglected. Due to the frequent evening thunderstorms and higher winds it was however perfect for a late afternoon lay...

    Liked On: 02-10-2020, 09:50 AM

11. 
    mark kiwi liked post by Wingman On thread : 6.5 Creedmoor load development

    This stage of the development is were it got hairy and disappointing and I very nearly scrapped the cal all together. From here on my once fired Lapua small primer brass was tumbled OAL trimmed,...

    Liked On: 02-10-2020, 09:28 AM

12. 
    mark kiwi liked post by rambo-6mmrem On thread : 6.5 Creedmoor load development

    94062 Started my creedmoor Journey today

    Liked On: 02-10-2020, 09:25 AM

13. 
    mark kiwi liked post by Wingman On thread : 6.5 Creedmoor load development

    Yip this will be a lengthy thread boys so sit back and grab a brew, Ill add to this write up over the next few days and as time allows Now before I even start on the journey to velocity and...

    Liked On: 02-10-2020, 09:24 AM

14. 
    mark kiwi liked post by Wingman On thread : 6.5 Creedmoor load development

    I have fairly recently entered the world of 6.5 Creedmoor after 20+ years of favouring .308win. I strayed to this fad/trendy cal with scepticism and apprehension but a lot of curiosity and sat down...

    Liked On: 02-10-2020, 09:21 AM

15. 
    mark kiwi liked post by Rushy On thread : HELLO :-)

    Welcome fellah.

    Liked On: 14-09-2020, 09:52 PM

Page 2 of 3 First 123 Last

• Jump to page: