Marty Henry
Member

2851 Likes

Page 138 of 191 First ... 3888124125126127128129130131132133134135136137138139140141142143144145146147148149150151152188 ... Last

• Jump to page:

1. 
   Marty Henry liked post by tetawa On thread : Parker hale rings

   The RAL S3 is low 1". The RAL S4 is low 26mm. The RAH S3 is high 1". The RAH S4 is high 26mm. There is also a 7/8" models but don't know the codes.

   Liked On: 26-10-2019, 07:56 AM

2. 
   Marty Henry liked post by Ryan_Songhurst On thread : Parker hale rings

   Just saw the RALS3 bit, the ones I have are those. Yours if you want them :) 122787

   Liked On: 25-10-2019, 09:47 PM

3. 
   Marty Henry liked post by mimms On thread : 2208 and 2206h powder for No.4 303

   3F :D

   Liked On: 21-10-2019, 09:11 PM

4. 
   Marty Henry liked post by Tentman On thread : Why not?

   Yup - I've been working on a similar project - but still in 303, just downloaded a bit, a 125gn at 2500-2600 with 30 gns of powder (I've found this amount suppresses really well). Still with a...

   Liked On: 21-10-2019, 04:12 PM

5. 
   Marty Henry liked post by FRST On thread : Am I being a dick?

   Got the Leupold base with the windage screw. Sorted the whole windage deal. I’ll probably be paying for it when I pick up the other project, but who knows, maybe they’ll come to the party. The...

   Liked On: 20-10-2019, 06:54 AM

6. 
   Marty Henry liked post by Russian 22. On thread : Permit required for importing projectiles now?

   why don't yah know...... read the legislation?

   Liked On: 19-10-2019, 09:54 AM

7. 
   Marty Henry liked post by Maca49 On thread : .577 snider enfield

   Or he was tapping the end of the cartridge to get it into the chamber, I’m an expert at it!!

   Liked On: 17-10-2019, 09:03 PM

8. 
   Marty Henry liked post by ChrisW On thread : Anyone with experience returning NZ with firearms

   A bit more background would help. Are you just coming for a hunt with the intention of taking the firearms back to your own country? Are you immigrating here and want to bring your firearms with...

   Liked On: 16-10-2019, 10:52 AM

9. 
   Marty Henry liked post by kiwijames On thread : First reloads

   Your firing pin is skinnier than the hole it pokes out of in the bolt. The primer will extrude back and into the gap between the two, hense the little ring around the strike mark in the primer....

   Liked On: 14-10-2019, 06:12 PM

10. 
    Marty Henry liked post by ChrisW On thread : Sako 85 issue

    Where it all turns to crap is that as soon as you modify the rifle without written consent it looses its warranty. It lost its warranty prior to the issue coming to light. Obviously the warranty...

    Liked On: 08-10-2019, 02:41 PM

11. 
    Marty Henry liked post by DPT On thread : DIY suppressor anyone

    Yeah made one or two over the last few years. :-)

    Liked On: 07-10-2019, 12:32 PM

12. 
    Marty Henry liked post by Tahr On thread : 6.5PRC

    Because it only produces a 5% increase in performance for a 45% increase in powder over the 6.5x55 all the reamers and custom builds have been packed up and taken to the dump and the factory rifles...

    Liked On: 07-10-2019, 06:44 AM

13. 
    Marty Henry liked post by DPT On thread : Sighting in with a suppressor

    It shouldnt, most of the time you will have a different point of impact shooting with it on or shooting with it off, but every time you put it back on it should shoot the same place as every other...

    Liked On: 06-10-2019, 07:10 AM

14. 
    Marty Henry liked post by Micky Duck On thread : Sighting in with a suppressor

    never noticed a difference AT ALL with taking it off then going back on....think about it....IF there was going to be a difference well then you would have to sight in AGAIN EVERY time you put it...

    Liked On: 06-10-2019, 06:59 AM

15. 
    Marty Henry liked post by Micky Duck On thread : Sighting in with a suppressor

    put it on,sight it in,go shoot stuff.....it will probably smoke a bit for first few shots (burning off oils in can) it will probably shoot about 3-4" below where it was before...eg using a bore...

    Liked On: 06-10-2019, 06:57 AM

Page 138 of 191 First ... 3888124125126127128129130131132133134135136137138139140141142143144145146147148149150151152188 ... Last

• Jump to page: