Marty Henry
Member

5128 Likes

Page 230 of 342 First ... 130180216217218219220221222223224225226227228229230231232233234235236237238239240241242243244280330 ... Last

• Jump to page:

1. 
   ZQLewis liked post by Marty Henry On thread : 3 Shot Cold Bore Group to 375yrds

   Oath, im not sure i could even see your aiming point at 500 yds. You must have a big arse scope.

   Liked On: 02-08-2019, 11:26 PM

2. 
   Bagheera liked post by Marty Henry On thread : Old 303 Ammo & old school hammer reloading

   Ive shot ammo i loaded in the 90s but then i know what was in it. I also regularly shoot mil slurp from the 50s and 60s with no issues apart from the occasional hangfire with some 40s stuff. A bit...

   Liked On: 02-08-2019, 11:01 PM

3. 
   40mm liked post by Marty Henry On thread : Casting.....lead, tin and Antimony supply?

   Scrap metal dealers are a good source but so is scrounging old building sites and indoor rifle clubs produce a suprising amount of lead. Wheel weights contain antimony plus lead rarely any tin, lead...

   Liked On: 02-08-2019, 09:16 PM

4. 
   omegaspeedy liked post by Marty Henry On thread : Casting.....lead, tin and Antimony supply?

   Also zinc melts nearly 100 degrees higher than lead antimong tin mixes so any wheel weights floating on to along with those little clips get binned. There have been attempts to cast zinc bullets...

   Liked On: 02-08-2019, 05:48 PM

5. 
   mimms liked post by Marty Henry On thread : .308 WIN Projectile Type/Weight Advice

   True but at that short distance parallax and focus problems can turn a 1/4 inch error into 1 inch at 100. A lot of people when zeroing accept maybe 1/2 either side of poi as being ok, thats a max...

   Liked On: 02-08-2019, 05:24 PM

6. 
   omegaspeedy liked post by Marty Henry On thread : Casting.....lead, tin and Antimony supply?

   Scrap metal dealers are a good source but so is scrounging old building sites and indoor rifle clubs produce a suprising amount of lead. Wheel weights contain antimony plus lead rarely any tin, lead...

   Liked On: 02-08-2019, 01:44 PM

7. 
   Kiwi Sapper liked post by Marty Henry On thread : Casting.....lead, tin and Antimony supply?

   Scrap metal dealers are a good source but so is scrounging old building sites and indoor rifle clubs produce a suprising amount of lead. Wheel weights contain antimony plus lead rarely any tin, lead...

   Liked On: 02-08-2019, 11:55 AM

8. 
   Micky Duck liked post by Marty Henry On thread : .223 off the shelf ammo

   Pretty devastating terminal performance with those IF you can hit the target.

   Liked On: 02-08-2019, 11:36 AM

9. 
   Nugget connaisseur liked post by Marty Henry On thread : .308 WIN Projectile Type/Weight Advice

   True but at that short distance parallax and focus problems can turn a 1/4 inch error into 1 inch at 100. A lot of people when zeroing accept maybe 1/2 either side of poi as being ok, thats a max...

   Liked On: 02-08-2019, 11:03 AM

10. 
    tanqueray liked post by Marty Henry On thread : Rolling block

    Being pedantic, the martini is a tipping block it pivots at the rear. The sharps, stevens, farhqson, are falling blocks that slide down to expose the chamber.

    Liked On: 02-08-2019, 09:33 AM

11. 
    Moa Hunter liked post by Marty Henry On thread : Casting.....lead, tin and Antimony supply?

    Scrap metal dealers are a good source but so is scrounging old building sites and indoor rifle clubs produce a suprising amount of lead. Wheel weights contain antimony plus lead rarely any tin, lead...

    Liked On: 02-08-2019, 09:10 AM

12. 
    Micky Duck liked post by Marty Henry On thread : .223 off the shelf ammo

    Correct, and konevs point about light ones with thin jackets in very fast twists is a good one. At 3200 fps a bullet fired from a 1:7 twist is doing 329,1000 rpm and that will rip a 40 grain varmit...

    Liked On: 01-08-2019, 09:28 PM

13. 
    dannyb liked post by Marty Henry On thread : Spur-winged plovers

    Breasted this one today from 180 yds with the 223, dont think ill bother making a pie from it.

    Liked On: 01-08-2019, 07:57 PM

14. 
    tetawa liked post by Marty Henry On thread : Large vs magnum rifle primer advice??

    The name magnum is a bit misleading. They produce a longer lasting ignition flame than standard primers which was found to be useful in getting the early double base ball powders used in military...

    Liked On: 01-08-2019, 09:37 AM

15. 
    stevodog liked post by Marty Henry On thread : Large vs magnum rifle primer advice??

    The name magnum is a bit misleading. They produce a longer lasting ignition flame than standard primers which was found to be useful in getting the early double base ball powders used in military...

    Liked On: 01-08-2019, 09:02 AM

Page 230 of 342 First ... 130180216217218219220221222223224225226227228229230231232233234235236237238239240241242243244280330 ... Last

• Jump to page: