Marty Henry
Member

4848 Likes

Page 271 of 324 First ... 171221257258259260261262263264265266267268269270271272273274275276277278279280281282283284285321 ... Last

• Jump to page:

1. 
   Beaker liked post by Marty Henry On thread : Dinner thread?

   Fancy name for dry cure bacon, bloody nice stuff.

   Liked On: 10-11-2017, 06:52 AM

2. 
   outlander liked post by Marty Henry On thread : Lee 1oz slug through a full choke.

   Slugs are loaded bare over usually a fibre wad NOT in a shot wad. You can cut the petals off a shot wad and use that if you wish. With round ball I used a cut down one with another cut to just the...

   Liked On: 09-11-2017, 07:36 PM

3. 
   nightshooter liked post by Marty Henry On thread : new era A5 browning ?

   I have an early 80s a5 12g, great semi get one.

   Liked On: 09-11-2017, 04:21 PM

4. 
   gadgetman liked post by Marty Henry On thread : 13,000 military-style semi-automatic weapons in NZ

   Up until the highlighted bit Mr Ticklepenny actually sounded more sensible and coherent than the president of the police assn does.

   Liked On: 09-11-2017, 11:50 AM

5. 
   Gibo liked post by Marty Henry On thread : You Wanna Come?

   Funniest thing Ive read in ages, but it breaks the golden rule what happens on tour stays on tour so thanks for the honesty. Most of us have had similar exploits Im sure.

   Liked On: 09-11-2017, 08:40 AM

6. 
   Nibblet liked post by Marty Henry On thread : 13,000 military-style semi-automatic weapons in NZ

   Up until the highlighted bit Mr Ticklepenny actually sounded more sensible and coherent than the president of the police assn does.

   Liked On: 09-11-2017, 07:48 AM

7. 
   Cordite liked post by Marty Henry On thread : How short on a 303?

   If its unbubbad so far (full wood etc) it may be worth selling and getting one thats been shortened in the forewood already. A mint no 2 fazakely went for $1100 at the ruahine auction and good no 1s...

   Liked On: 07-11-2017, 11:59 PM

8. 
   Cordite liked post by Marty Henry On thread : How short on a 303?

   For short range in close cover forget speed concentrate on bullet weight and ideally use a round nosed one, 150 or 180 should be fine. As to barrel length jungle carbine length 20 inch is probably...

   Liked On: 07-11-2017, 11:58 PM

9. 
   john m liked post by Marty Henry On thread : How short on a 303?

   For short range in close cover forget speed concentrate on bullet weight and ideally use a round nosed one, 150 or 180 should be fine. As to barrel length jungle carbine length 20 inch is probably...

   Liked On: 07-11-2017, 06:47 AM

10. 
    Cordite liked post by Marty Henry On thread : Habits of Goats

    A good place to start would be the doc hunting permit application website, theres a section attached on what to hunt that covers goats habits and range quite well. Other species are also covered if...

    Liked On: 06-11-2017, 10:44 PM

11. 
    Gibo liked post by Marty Henry On thread : Habits of Goats

    Wish I could do that link thing, guess that means I must be an old goat not being able to do this interface thingie, but dont think of stalking me as this old goat can biteback

    Liked On: 06-11-2017, 02:34 PM

12. 
    Shootm liked post by Marty Henry On thread : 308 Max loads

    52 grains is case capacity to top of neck, so 46 should be the practical limit. If you must have more speed or powder capacity a 3006 reamer is the answer, after all the 308 is just a 3006 that didnt...

    Liked On: 05-11-2017, 05:14 PM

13. 
    Micky Duck liked post by Marty Henry On thread : most accurate center fire semi

    Well its not my sks! Does what I wanted it for perfectly but target rifle she aint

    Liked On: 05-11-2017, 01:24 PM

14. 
    Micky Duck liked post by Marty Henry On thread : 308 Max loads

    52 grains is case capacity to top of neck, so 46 should be the practical limit. If you must have more speed or powder capacity a 3006 reamer is the answer, after all the 308 is just a 3006 that didnt...

    Liked On: 05-11-2017, 01:22 PM

15. 
    veitnamcam liked post by Marty Henry On thread : Steel for gongs

    See Alistair at Ashurst engineering, Bis 80would be the minimum hardness you want, preferably AR 400, or Brinel 400 or ideally 500 would last for ever.

    Liked On: 04-11-2017, 03:53 PM

Page 271 of 324 First ... 171221257258259260261262263264265266267268269270271272273274275276277278279280281282283284285321 ... Last

• Jump to page: