MGNZ
Member

99 Likes

Page 5 of 7 First 1234567 Last

• Jump to page:

1. 
   stug liked post by MGNZ On thread : 3D print extended Tikka T3 Magazine

   First print came out OK. needs a bit of refining, but the magazine functions. 88817

   Liked On: 05-06-2018, 07:42 PM

2. 
   veitnamcam liked post by MGNZ On thread : 3D print extended Tikka T3 Magazine

   I needed 50 thou more mag length for my 300WM - managed to get my hands on a 3D model of the std Long Tikka mag body and thinned out the end walls. This should hold rounds up to ~3.46" COAL - vs...

   Liked On: 03-06-2018, 10:02 PM

3. 
   Willus liked post by MGNZ On thread : 3D print extended Tikka T3 Magazine

   I needed 50 thou more mag length for my 300WM - managed to get my hands on a 3D model of the std Long Tikka mag body and thinned out the end walls. This should hold rounds up to ~3.46" COAL - vs...

   Liked On: 03-06-2018, 08:36 PM

4. 
   SlimySquirrel liked post by MGNZ On thread : 3D print extended Tikka T3 Magazine

   I needed 50 thou more mag length for my 300WM - managed to get my hands on a 3D model of the std Long Tikka mag body and thinned out the end walls. This should hold rounds up to ~3.46" COAL - vs...

   Liked On: 02-06-2018, 05:18 PM

5. 
   Beetroot liked post by MGNZ On thread : 3D print extended Tikka T3 Magazine

   I needed 50 thou more mag length for my 300WM - managed to get my hands on a 3D model of the std Long Tikka mag body and thinned out the end walls. This should hold rounds up to ~3.46" COAL - vs...

   Liked On: 02-06-2018, 03:00 PM

6. 
   wsm junkie liked post by MGNZ On thread : 3D print extended Tikka T3 Magazine

   I needed 50 thou more mag length for my 300WM - managed to get my hands on a 3D model of the std Long Tikka mag body and thinned out the end walls. This should hold rounds up to ~3.46" COAL - vs...

   Liked On: 02-06-2018, 12:38 PM

7. 
   Bryan liked post by MGNZ On thread : 3D print extended Tikka T3 Magazine

   I needed 50 thou more mag length for my 300WM - managed to get my hands on a 3D model of the std Long Tikka mag body and thinned out the end walls. This should hold rounds up to ~3.46" COAL - vs...

   Liked On: 02-06-2018, 10:08 AM

8. 
   dannyb liked post by MGNZ On thread : 3D print extended Tikka T3 Magazine

   I needed 50 thou more mag length for my 300WM - managed to get my hands on a 3D model of the std Long Tikka mag body and thinned out the end walls. This should hold rounds up to ~3.46" COAL - vs...

   Liked On: 02-06-2018, 10:07 AM

9. 
   Morepork liked post by MGNZ On thread : DIY Induction Annealer

   it's rough looking but works good. video of it in action at the bottom. 85844 85843 Video In Action (https://www.dropbox.com/s/f2wb2vwdma6n70p/Video%2016-04-18%2C%207%2057%2058%20PM.mov?dl=0) ...

   Liked On: 26-05-2018, 02:59 AM

10. 
    The Claw liked post by MGNZ On thread : DIY Induction Annealer

    This project is pretty much finished now. video below of doing some 270 brass in free run mode. I did 75pc of 223 brass without pausing - the coil remains cool and the only parts that were...

    Liked On: 01-05-2018, 11:30 PM

11. 
    300CALMAN liked post by MGNZ On thread : DIY Induction Annealer

    This project is pretty much finished now. video below of doing some 270 brass in free run mode. I did 75pc of 223 brass without pausing - the coil remains cool and the only parts that were...

    Liked On: 01-05-2018, 09:27 PM

12. 
    40mm liked post by MGNZ On thread : DIY Induction Annealer

    This project is pretty much finished now. video below of doing some 270 brass in free run mode. I did 75pc of 223 brass without pausing - the coil remains cool and the only parts that were...

    Liked On: 01-05-2018, 08:40 PM

13. 
    303Guy liked post by MGNZ On thread : DIY Induction Annealer

    it's rough looking but works good. video of it in action at the bottom. 85844 85843 Video In Action (https://www.dropbox.com/s/f2wb2vwdma6n70p/Video%2016-04-18%2C%207%2057%2058%20PM.mov?dl=0) ...

    Liked On: 28-04-2018, 06:33 PM

14. 
    300CALMAN liked post by MGNZ On thread : DIY Induction Annealer

    Hi 300CALMAN, some pics below of the inside and arduino pinout and also some links to the bits from aliexpress and the software source. ZVS induction board...

    Liked On: 25-04-2018, 05:54 AM

15. 
    Beaker liked post by MGNZ On thread : DIY Induction Annealer

    Hi 300CALMAN, some pics below of the inside and arduino pinout and also some links to the bits from aliexpress and the software source. ZVS induction board...

    Liked On: 24-04-2018, 09:53 PM

Page 5 of 7 First 1234567 Last

• Jump to page: