Micky Duck
Member

44871 Likes

Page 1129 of 2992 First ... 12962910291079111511161117111811191120112111221123112411251126112711281129113011311132113311341135113611371138113911401141114211431179122916292129 ... Last

• Jump to page:

1. 
   Micky Duck liked post by Tahr On thread : 223 on deer

   Home now. They were 240 yards (above). Yearling side on low heart shot. Staggered 5 yards and tipped over. I could see blood spraying all over the place through my scope. Mum ran 20 yards and stopped...

   Liked On: 16-06-2023, 06:27 PM

2. 
   Micky Duck liked post by Sauer On thread : Possums with a recurve crossbow

   We use Cold Steel Cheap Shot broadheads on possums. They are a pretty hardy animal and we found that the blunt heads made them very crook but didn’t kill them. Unless you’re shooting at possums on...

   Liked On: 16-06-2023, 06:25 PM

3. 
   Micky Duck liked post by Friwi On thread : Possums with a recurve crossbow

   In the 90,s we were using something called the scorpion claws, made by zwickey, the same guys who made the judo point. You were sliding it onto your aluminium shat behind what ever point you were...

   Liked On: 16-06-2023, 06:24 PM

4. 
   Micky Duck liked post by 6.5 CRD On thread : Lapua 6.5 PRC Brass - Split Necks

   Interesting, will take the expander ball out and so some measuring. Although i find it strange its only some cases that go bad, majority of them are perfectly fine. Same dies that i used for my last...

   Liked On: 16-06-2023, 06:24 PM

5. 
   Micky Duck liked post by dale On thread : Lapua 6.5 PRC Brass - Split Necks

   Also what I did that made me help identify my problem was, measuring the new next, then a fired neck. Then full length size but without the expander ball and then re size again with the expander ball...

   Liked On: 16-06-2023, 06:23 PM

6. 
   Micky Duck liked post by dale On thread : Lapua 6.5 PRC Brass - Split Necks

   Yeh iv been down this rabbit hole. I did returned my brass back to the supplier and they said it was a bad batch, however I’m not convinced. I have done annealing on the same brass with no change to...

   Liked On: 16-06-2023, 06:23 PM

7. 
   Micky Duck liked post by SmokeyJason On thread : I get lucky

   My brother was down for a few days so I spend one of them being a tourist and a brother. Driving thru a medium large town we ducked into a sports store, looked at some mini knives( cute as but eye...

   Liked On: 16-06-2023, 06:12 PM

8. 
   Micky Duck liked post by akaroa1 On thread : DIY bullet tips for flat nosed cast bullets

   Oh dear someone has gone down a deep dark hole

   Liked On: 16-06-2023, 06:00 PM

9. 
   Micky Duck liked post by Billbob On thread : Best wood for making bows

   Josh James has a youtube video on making a longbow and he uses Kanuka

   Liked On: 15-06-2023, 08:13 PM

10. 
    Micky Duck liked post by Tentman On thread : Best wood for making bows

    The Tanekaha suggestion is interesting, it's a very nice tough timber, definitely less brittle than Macrocarpa. My yacht is Tanekaha below the waterline, Macrocarpa above. From nudging various...

    Liked On: 15-06-2023, 08:13 PM

11. 
    Micky Duck liked post by Tahr On thread : 223 on deer

    Those Hammers! 226671

    Liked On: 15-06-2023, 08:05 PM

12. 
    Micky Duck liked post by Pengy On thread : Possum fur

    Just got home to find that the dog found my stash and redistributed it around my spare room. Silly me for leaving it in reach, but bloody funny all the same

    Liked On: 15-06-2023, 05:23 PM

13. 
    Micky Duck liked post by Finnwolf On thread : Is this 'fair'?

    Yup, might lose them if I took them out!

    Liked On: 15-06-2023, 05:07 PM

14. 
    Micky Duck liked post by Finnwolf On thread : Is this 'fair'?

    In the 70’s during duck shooting season I used to leave my shotgun on top of the back of the seat in my old ute, couldn’t lock the ute but even sitting parked outside a pub the shotgun never got...

    Liked On: 15-06-2023, 04:51 PM

15. 
    Micky Duck liked post by 6.5 CRD On thread : Lapua 6.5 PRC Brass - Split Necks

    Firing is when its cracking. They didnt look like this when i sized them & loaded last batch. Didnt notice any accuracy issues or anything weird, took all the brass ultrasonic cleaned & tumbled it...

    Liked On: 15-06-2023, 03:35 PM

Page 1129 of 2992 First ... 12962910291079111511161117111811191120112111221123112411251126112711281129113011311132113311341135113611371138113911401141114211431179122916292129 ... Last

• Jump to page: