Micky Duck
Member

45292 Likes

Page 1825 of 3020 First ... 825132517251775181118121813181418151816181718181819182018211822182318241825182618271828182918301831183218331834183518361837183818391875192523252825 ... Last

• Jump to page:

1. 
   Micky Duck liked post by Woody On thread : traditions

   Tradition here was a "young farmers" pre season clay bird shoot and also 3 or 4 clay shoots on a farm for wildfowlers assn along with bbq. These are good social events with youngsters included under...

   Liked On: 01-05-2022, 09:15 PM

2. 
   Micky Duck liked post by Kelton On thread : Lapua 308 brass resizing to 260

   I stand corrected I ment with the muddled up head stamps of 08 based cartridges.308 parent . I seem to remember a yarn at the handloaders in Christchurch about a 3006 spraying rounds everywhere...

   Liked On: 01-05-2022, 09:08 PM

3. 
   Micky Duck liked post by Pommy On thread : Loading 7.62x39 subsonic from steel cased factory ammo

   I've also been impressed with the SubX so far. Here's one recovered after passing through a wallaby's chest and burying in the dirt. 195597 And here's a headshot. Small entry between the eyes....

   Liked On: 01-05-2022, 08:51 PM

4. 
   Micky Duck liked post by Bill999 On thread : Loading 7.62x39 subsonic from steel cased factory ammo

   nothing wrong with subs out of the 7.62x39 except when you miss you have to say "ах дерьмо" instead of "ah shit" in regards to storing up brass I usually only load up between 20 and 30 at a time....

   Liked On: 01-05-2022, 08:51 PM

5. 
   Micky Duck liked post by Bill999 On thread : Loading 7.62x39 subsonic from steel cased factory ammo

   in my 300blk im using 190 subx I have a cast 151 load Iv built up for both my 308 and 300blk that I use interchangeably I still have a fair few boxes of subx and I used up all my loaded cast ones...

   Liked On: 01-05-2022, 08:50 PM

6. 
   Micky Duck liked post by Finnwolf On thread : Loading 7.62x39 subsonic from steel cased factory ammo

   This is a ‘one day’ plan of mine, got a heap of military ammo and some Trailboss and a bullet puller and dies so far.

   Liked On: 01-05-2022, 08:50 PM

7. 
   Micky Duck liked post by Bill999 On thread : Loading 7.62x39 subsonic from steel cased factory ammo

   I use 30cal subs for everything these days, in 300blk It works well on everthing from turkeys to home kill bulls shots need to sever the spine(hard) or scramble the brain(less hard) I site for...

   Liked On: 01-05-2022, 08:50 PM

8. 
   Micky Duck liked post by stumpys On thread : Izzies Clement Mill 8 pt Sika

   Was driving a dirty ol'd22 navara. It would have stood out amoungst all the Rangers and other shinies - my old mud slut ain't pretty

   Liked On: 01-05-2022, 08:38 PM

9. 
   Micky Duck liked post by 6x47 On thread : Lapua 308 brass resizing to 260

   Managed something similar once at our Club. Fired off the first lot of 6.5x47 , all good. Next shoot, same wind conditions, first shot -nothing- appeared on the tablet. WTF?? same again second shot....

   Liked On: 01-05-2022, 08:37 PM

10. 
    Micky Duck liked post by grandpamac On thread : Lapua 308 brass resizing to 260

    For some cartridges this is true but not the .308 family. There is enough difference to prevent , say a .260 chambering in a .243. The trouble spot is between .270 and 7mm where the difference is...

    Liked On: 01-05-2022, 07:54 PM

11. 
    Micky Duck liked post by Cigar On thread : Lapua 308 brass resizing to 260

    I thought it was the other way round, i.e. lengths were different to prevent chambering larger calibres in small chambers. I much rather fire a 243 round in a 308 rifle than vice-versa!

    Liked On: 01-05-2022, 07:52 PM

12. 
    Micky Duck liked post by grandpamac On thread : Lapua 308 brass resizing to 260

    Sorry but this is not true. To my knowledge all of the .308 family of cartridges have a length to shoulder of 1.56" (39.62mm). The length to the base of the neck differs due to changes in diameter. A...

    Liked On: 01-05-2022, 07:52 PM

13. 
    Micky Duck liked post by johnd On thread : Lapua 308 brass resizing to 260

    I have done it. If you start with thick necks like Lapua ( @15 thou) by the time it's at .260 the necks will be around 17 thousands plus. Then you will need to neck trim. Even if you get away...

    Liked On: 01-05-2022, 07:52 PM

14. 
    Micky Duck liked post by veitnamcam On thread : Lapua 308 brass resizing to 260

    Sell the 308 brass and buy 6.5mm projectiles

    Liked On: 01-05-2022, 07:51 PM

15. 
    Micky Duck liked post by Cyclops On thread : New range laws and shooting on unregistered ranges

    If the same approach was applied to other sports there'd be no rugby, no motorsport, cycling would be heavily restricted.

    Liked On: 01-05-2022, 07:44 PM

Page 1825 of 3020 First ... 825132517251775181118121813181418151816181718181819182018211822182318241825182618271828182918301831183218331834183518361837183818391875192523252825 ... Last

• Jump to page: