I had the honour of flying a Russian Steppe eagle one time. It was something I wont forget in a hurry. The owner/trainer told me after the event, that I was the only person to ever handle her...
Liked On: 04-07-2020, 09:54 PM
KFM Kiwi Fried Moa
Liked On: 04-07-2020, 09:54 PM
https://uploads.tapatalk-cdn.com/20200704/90e73dac94d623d5a21eb33aaa4c22b8.jpg Sent from my iPhone using Tapatalk
Liked On: 04-07-2020, 09:40 PM
Not a chance could not have taken enough material off to allow it to fit, definitely happy with the current set up it's much nicer to carry this way :thumbsup:
Liked On: 04-07-2020, 08:56 PM
Deceiving with the winter coats I think. They were in good condition. Saw a few Reds but never go a shot. Those 2 in the pic with me in the other thread was the latest (darkest) I have ever shot a...
Liked On: 04-07-2020, 08:48 PM
Oh well at this stage I had a few options, I could move the swivel stud forward (easiest). I could opt to only use the bipod in free panning (stupid as I often use it locked as I prefer it). ...
Liked On: 04-07-2020, 03:54 PM
Greetings All, In my experience partial sizing works best in more tapered cases, like the 6.5 x 55, .30-06 etc when loaded to lower pressure. Cases like the .308 often do better with either minimal...
Liked On: 04-07-2020, 03:49 PM
Many years ago with a rush of blood to the head i decided my BLR needed a good clean and so removed the pins that go through the receiver and removed the lever and bolt mechanisim . My memory is a...
Liked On: 04-07-2020, 02:45 PM
I've been using the Barnes 129 grn LRX at 3250. They seem a bit softer than the TTSX. Have been very happy with them out to 450 yds, but these Hammers are looking better. Im skinning the deer from...
Liked On: 04-07-2020, 02:29 PM
Edit to title "Hammer Hunter" Entry at at 220 yds angled in quartering away: 144151 And the exit 144152
Liked On: 04-07-2020, 02:18 PM
Tried the 117 grn @3450fps out of my 270wsm this evening. Buck at 300yds and 2 others @220 yds. 3 one shot kills. A lot more organ damage than the 130 Barnes and larger in and out out holes. Very...
Liked On: 04-07-2020, 11:22 AM
Hey all sorted now thanks mate getting a 1/4 lab 1/4 gsp 1/2 Vizsla cheers
Liked On: 04-07-2020, 11:19 AM
Bolt a bit scratchy,gave it a good clean n weee spot of oil.Ye five in the mag plenty.Got a few boxes of Belmont Hornady 50gr sp.If it shoots as good as the vixen il be pleased.
Liked On: 03-07-2020, 08:30 PM
The first mill cut out .650" slot and I needed .735" per the plans, so after a reset up to get it lined up on centre I mounted a broken mill cutter with only one cutting flute. Set in the four jaw...
Liked On: 03-07-2020, 06:45 PM
I have to admire your tenacity! That is lot of work without a milling slide, buggerizing around with packers and a dial gauge before you can make a cut! It just goes to show what can be done on a...
Liked On: 03-07-2020, 06:44 PM