Micky Duck
Member

44874 Likes

Page 443 of 2992 First ... 3433934294304314324334344354364374384394404414424434444454464474484494504514524534544554564574935439431443 ... Last

• Jump to page:

1. 
   Micky Duck liked post by woods223 On thread : Warm winter sleepingbag

   Old man, ex-deer culler, taught me to do same. Takes a bit longer to get dressed in morning but usually sleep nice and warm. Two weeks ago slept in clothes worn during the day, about -16C, first time...

   Liked On: 30-05-2024, 04:35 PM

2. 
   Micky Duck liked post by robhughes-games On thread : HGPRECISION. Cnc gunsmithing and services

   There are a few options available. I hadn't looked at it but entirely possible. Judt have to make sure I don't spread myself out too thin...be good to have a few base products selling to help pay for...

   Liked On: 30-05-2024, 04:34 PM

3. 
   Micky Duck liked post by Marty Henry On thread : Reloading 22 Hornet (The Original) – Optimal Canada Goose Load

   It would be nice if they just sat there after the first shot

   Liked On: 30-05-2024, 04:27 PM

4. 
   Micky Duck liked post by 308 On thread : Fixing basic gun racks to studs

   14g tek screws or purlin screws 100mm long Burr them out completely and keep battery powered driver nearby for inspection to demonstrate that they are rounded off Come removal time, cut head...

   Liked On: 30-05-2024, 04:25 PM

5. 
   Micky Duck liked post by Happy Jack On thread : Fixing basic gun racks to studs

   I have a simple rack in the caravan bolted to the chassis using snap off nuts which leave behind a round tapered nut when the hex part breaks off. I tried gripping them with pliers etc and they just...

   Liked On: 30-05-2024, 04:24 PM

6. 
   Micky Duck liked post by Ranger 888 On thread : Fixing basic gun racks to studs

   I'm selling 6- gun racks with mounting bolts that that can't be tampered with. They've passed 2 police inspections. They are heavy, not sure what a courier would charge, but I'm selling them for $50....

   Liked On: 30-05-2024, 04:23 PM

7. 
   Micky Duck liked post by No.3 On thread : Kmart/Campmaster "Jetboil"

   I just got one sent out, just ordered one online and put my address in etc...

   Liked On: 30-05-2024, 03:36 PM

8. 
   Micky Duck liked post by Tahr On thread : 223 over resized brass?

   I did that once with a .223. Screwed the die down too far. Used them and no head separation or dramas. I checked them using the same tool as Tentman and they were a few though under spec.

   Liked On: 30-05-2024, 03:19 PM

9. 
   Micky Duck liked post by 7mm Rem Mag On thread : 223 over resized brass?

   From memory I bought some 223 hornady brass off trademe which had been oversized, the extremely bad ones I biffed and the others I loaded and fired them probably blowing a few rabbits away. After...

   Liked On: 30-05-2024, 03:17 PM

10. 
    Micky Duck liked post by gimp On thread : 223 over resized brass?

    What does it measure once fired out of your rifle?

    Liked On: 30-05-2024, 03:17 PM

11. 
    Micky Duck liked post by grandpamac On thread : how little reworking of the brass while reloading is necessary

    Those are fighting words blip, The last person I heard utter those words was seen barely an hour later sheepishly retreating from the mound with a cartridge firmly stuck in his rifles chamber. Came...

    Liked On: 30-05-2024, 03:11 PM

12. 
    Micky Duck liked post by Marty Henry On thread : how little reworking of the brass while reloading is necessary

    Full length sizing lengthens cases meaning trimming is required. Neck sizing just enough to hold the projectile tightly is much more brass friendly and results in longer case life. It sort of depends...

    Liked On: 30-05-2024, 03:11 PM

13. 
    Micky Duck liked post by Slug On thread : how little reworking of the brass while reloading is necessary

    Yeah...nah. The more bang bang, the harder and longer it gets, until one day forcing it in only ends in tears.

    Liked On: 30-05-2024, 03:11 PM

14. 
    Micky Duck liked post by Tentman On thread : how little reworking of the brass while reloading is necessary

    Haha - eventually you'll end up with a loaded round stuck in the chamber refusing to be extracted . . . . Same thing happens when you only neck size. I gave up neck sizing only for this reason,...

    Liked On: 30-05-2024, 03:11 PM

15. 
    Micky Duck liked post by Frogfeatures On thread : Using one powder across multiple calibres.

    I used it in my Baikal 223, worked well. ( 23” barrel ) When I swapped to a Savage with an 18” barrel, I swapped to 2206h, but I imagine the 2208 would still work It’s just 2206h is a little...

    Liked On: 29-05-2024, 09:53 PM

Page 443 of 2992 First ... 3433934294304314324334344354364374384394404414424434444454464474484494504514524534544554564574935439431443 ... Last

• Jump to page: