Thanks guys, I got the reply below from ADI. It seems rather conservative so I guess their lawyers wrote it rather than their Development techs, I get it, the have to keep everyone safe in a...
Liked On: 13-05-2024, 07:13 PM
What type of shooting or hunting will you use it for? A scope for the bush is a lot different to a scope for long range shooting/targets.
Liked On: 13-05-2024, 07:08 PM
I’m running a Nightforce SHV 5-20 on my 7mm rem mag and have very been very impressed with it for their “entry level” scope. It’s taken a few bangs and fell off the yet and still shoots true. I...
Liked On: 13-05-2024, 07:08 PM
We had an eventful evening together yesterday. Shot some deer and enjoyed each others' company. I shot a doe standing on the scrub edge at 100 yards. She looked hard hit by the .223 but bolted...
Liked On: 13-05-2024, 06:59 PM
hamishg I got a pair of varipower Binos (8-24x50 ) for the reason you listed in the OP however, they sit in the lounge and I take the 10x with me. I find the heavier pair simply did not get used. At...
Liked On: 13-05-2024, 06:56 PM
Unless you carry a tripod 15x will be worthless. Putting a pair of 10x binos on a tripod shows how bad hand holding is with 10x, 15x will be considerably worse. Personally I wouldn't think you...
Liked On: 13-05-2024, 06:55 PM
to hold 15x steady one really needs to have them on a tripod - so why not just get a spotting scope - say 20-60 usefull for sighting in as well - I use 10x binos and they can be hard to hold still...
Liked On: 13-05-2024, 06:54 PM
So what the BP cast lead load is screaming at me is that the nitro load that only half filled the case is very inconsistent and that the BP load which is 105% full is very consistent I had better...
Liked On: 13-05-2024, 06:52 PM
I can confirm that it like Black Powder 360 grain cast powder coated loads. 50 grains 1 1/2 FG and over powder card slightly compressed 250199 250200
Liked On: 13-05-2024, 06:52 PM
I forgot to mention re the Epoxy Acetone clean all the parts prior to final epoxy fitting Mix about 3 or 4 table spoons worth of it to get it well mixed and accurate. Put plenty on as the liner...
Liked On: 13-05-2024, 12:21 PM
For anyone interested in how this conversion was done here are some missing details on the process I used. There are clearly a lot of little tips and tricks. Just remember when epoxying in a...
Liked On: 13-05-2024, 12:21 PM
I was running it with a little toilet paper filler because 4198 only half filled the case
Liked On: 13-05-2024, 12:18 PM
I sorta kinda maybe thought I'd give away the knifemaking for a while, but then decided I wanted a couple of knives which had edges that curved quite gradually up to the point, and without a...
Liked On: 12-05-2024, 08:52 PM
The Czech 8x57 mauser I've been using is a repeatable 1-1/2 moa group at a hundy with the ammo I've been using. Haven't tried anymore since it's been sighted in properly. Me and a mate who is a...
Liked On: 12-05-2024, 07:23 PM
many thanks No 3 common sense -what are you trying to achieve - many on here seem to be just target shooters or trying loads out - if I zero for hunting I dont waste ammo - hit the right spot...
Liked On: 12-05-2024, 07:22 PM