Micky Duck
Member

44874 Likes

Page 805 of 2992 First ... 30570575579179279379479579679779879980080180280380480580680780880981081181281381481581681781881985590513051805 ... Last

• Jump to page:

1. 
   Micky Duck liked post by TeRei On thread : DPT New big barrel suppressor

   Mate. Think Darren will not be upset. Got original TOK cans personally from him. All our guns , all 5 sport DPT. Enuff said.

   Liked On: 07-11-2023, 07:32 PM

2. 
   Micky Duck liked post by Trout On thread : Riverbed

   I have NZ Maps app (premium) on my phone,cost about $12 a year.Got everything you need to know with mapping in nz,hunting areas,tracks,huts and a lot of maps selections you can have.You dont need...

   Liked On: 07-11-2023, 06:53 PM

3. 
   Micky Duck liked post by Kelton On thread : Blooding the new .308

   Correct only because I dropped a mates brand spanking magnum dpt when I had his rifle for the load development and put a small mark on the rear section but it was brand spanking so I did right and...

   Liked On: 07-11-2023, 06:52 PM

4. 
   Micky Duck liked post by Kelton On thread : Blooding the new .308

   Mines fixed parallex but is fine for my use certainly is limited options when zooms so “low”

   Liked On: 07-11-2023, 06:51 PM

5. 
   Micky Duck liked post by XR500 On thread : 1974 Tohatsu B18D outboards

   Correct. My 1976 85hp Johnson outboard sent me spare trying to figure out where the tell tale should be coming out. In the end I twigged, and looked it up on line. So just carried one of those cheap...

   Liked On: 07-11-2023, 05:35 PM

6. 
   Micky Duck liked post by Marty Henry On thread : show us your chainsaws

   Yes the huskies resting, it's limbed most of the head already. Stuff waving a 12 kg one around for that job.

   Liked On: 07-11-2023, 05:34 PM

7. 
   Micky Duck liked post by Marty Henry On thread : show us your chainsaws

   After doing 15 cube of Mac and slabbing a bit as well some old man pine beckoned. It looked big standing up but it seems even bigger lying down. We have our work cut out for us getting this split....

   Liked On: 07-11-2023, 05:21 PM

8. 
   Micky Duck liked post by vulcannz On thread : Sighting in your hunting rifle

   For my centerfires I go figure out the 2" square Point BlanC (

   Liked On: 07-11-2023, 05:18 PM

9. 
   Micky Duck liked post by Russian 22. On thread : 1974 Tohatsu B18D outboards

   I got two running motors (a short and a long shaft) and a parts motor for 470 bucks. So far I have found gaskets, carburetor rebuild kits etc. When I get the manual I should be able to confirm the...

   Liked On: 07-11-2023, 05:15 PM

10. 
    Micky Duck liked post by Marty Henry On thread : Has anyone ever lightened the springs in a B/O shotgun?

    Leave it cocked and empty that usually weakens springs

    Liked On: 07-11-2023, 05:13 PM

11. 
    Micky Duck liked post by Marty Henry On thread : Has anyone ever lightened the springs in a B/O shotgun?

    If it's anything like the Kahn a neighbor brought it's not just springs but the fit of the barrels to the receiver. Even when cocked it was still stiff but it eased up after a few hundred openings...

    Liked On: 07-11-2023, 05:12 PM

12. 
    Micky Duck liked post by country cuts On thread : Has anyone ever lightened the springs in a B/O shotgun?

    Try it with out any shells in it if it is still the same check to make sure there aren't any burs or tool marks on the locking mechanism or under the lever. Might need a good bit of use and a clean...

    Liked On: 07-11-2023, 05:12 PM

13. 
    Micky Duck liked post by JoshC On thread : Quick weekend tahr hunt

    Did a quick mission up to Canterbury in the weekend to look for a spring bull tahr before we all get too busy as the year winds down! A pretty goood leg stretch in the morning stomping our way in,...

    Liked On: 07-11-2023, 05:09 PM

14. 
    Micky Duck liked post by Delphus On thread : Character building

    Well I got it out of the clamps and gave it a quick sand up. It actually came up ok. The join is visible under the right light but not hugely obvious. It’s still straight too so I think it’s actually...

    Liked On: 07-11-2023, 05:07 PM

15. 
    Micky Duck liked post by Roarless20 On thread : 22 cal smoothbore vs rifled 22lr bore RE SHOT SHELLS

    I don't know but my thinking is you will want to be bloody careful with putting a suppressor on there using shot. I've seen shotgun pellets leave barrels at near 45deg in low light so I can't see why...

    Liked On: 07-11-2023, 05:04 PM

Page 805 of 2992 First ... 30570575579179279379479579679779879980080180280380480580680780880981081181281381481581681781881985590513051805 ... Last

• Jump to page: