Moa Hunter
Banned

15704 Likes

Page 341 of 1047 First ... 241291327328329330331332333334335336337338339340341342343344345346347348349350351352353354355391441841 ... Last

• Jump to page:

1. 
   Moa Hunter liked post by mcche171 On thread : Suppressors

   I have all that has been stated above. DPT - Good value, strong, but old tecnology and not the quietest. Plus my baffles went far too early on my 308. Stores push them as they are like a lego set...

   Liked On: 23-06-2022, 09:24 AM

2. 
   Moa Hunter liked post by Ross Nolan On thread : Suppressors

   What was the recoil like? Richard at Serious Shooters launched one off a 45/70 years ago by shooting slow burning powder out of a v short barrel, and filling the can with unburned powder (I seem to...

   Liked On: 23-06-2022, 09:16 AM

3. 
   Moa Hunter liked post by Sauer On thread : Suppressors

   I have an A-Tec Optima and it is noticeably quieter than my mates Gunworks suppressor. I also have an older (about 10 years) Greystone which is okay, but Stuart was such a dickhead to deal with I’d...

   Liked On: 23-06-2022, 09:15 AM

4. 
   Moa Hunter liked post by woods223 On thread : Suppressors

   Ffs, I don’t know what some of you do with your suppressors to go through so many. Pest control work on goats,pigs,deer,etc, suppressors are good for 5000 rounds or so. The suppressor wore...

   Liked On: 23-06-2022, 09:14 AM

5. 
   Moa Hunter liked post by Kimber 7mm-08 On thread : Widowmakers

   Good reminder to always look up before you put your tent down in the bush.

   Liked On: 23-06-2022, 12:22 AM

6. 
   Moa Hunter liked post by Ranger 888 On thread : Widowmakers

   They were named widow makers by the early kauri loggers. A lot of them were killed by the falling astelia clumps, some of which weighed over a tonne. Which begs 2 questions: being widow makers, does...

   Liked On: 23-06-2022, 12:22 AM

7. 
   Moa Hunter liked post by Bagheera On thread : Widowmakers

   Astelias growing in trees are a natural hazard. When it rains, they get heavy and fall on the nice flat open tent sites below. A pig has excavated a nice hollow in the soft ground here. 199954 ...

   Liked On: 23-06-2022, 12:22 AM

8. 
   Moa Hunter liked post by silentscope On thread : Who knows their shit?

   Looks like goat shit, and since you've seen goats there before that would make it more likely to be a goat. Im sure we've all spent time looking at goat shit wishing it was a deer

   Liked On: 22-06-2022, 12:58 PM

9. 
   Moa Hunter liked post by vulcannz On thread : Who knows their shit?

   Does it taste salty?

   Liked On: 22-06-2022, 12:58 PM

10. 
    Moa Hunter liked post by XR500 On thread : Who knows their shit?

    A fallow hind is my guess too. They seem quite capable of hiding in plain sight in crappy grass, scrub and other small patches of cover, and appear happy being in close contact with human made...

    Liked On: 22-06-2022, 12:58 PM

11. 
    Moa Hunter liked post by GWH On thread : 7mm08 120gr vs 140gr nosler bt

    If you will be shooting out a bit further go with the 140's, they simply hold more energy out further. I've run both in my 15" 708 bushpig. At close range the 120 NBT went thru 3 goats standing...

    Liked On: 22-06-2022, 12:51 PM

12. 
    Moa Hunter liked post by TeRei On thread : Downloading / Reduced loads for youth or recoil sensitive shooters

    Clearly he enjys using it. Winner.

    Liked On: 22-06-2022, 12:40 PM

13. 
    Moa Hunter liked post by Tahr On thread : New Southern Lite Pack

    The guy who makes them is colour blind and Im slightly, especially with greens and browns (one of my son's is quite colour blind - sees deer as black - they stick out for him like in night vision)....

    Liked On: 22-06-2022, 12:34 PM

14. 
    Moa Hunter liked post by Mick Hunter On thread : New Southern Lite Pack

    What’s the pouch hanging off the bottom for? Empty brass?

    Liked On: 21-06-2022, 09:25 PM

15. 
    Moa Hunter liked post by m101a1 On thread : What reputable caliper manufacturers are out there?

    Got a kingchrome that shit so Im going to set at 125.1 mm and weld in position as a Paua measure

    Liked On: 21-06-2022, 09:18 PM

Page 341 of 1047 First ... 241291327328329330331332333334335336337338339340341342343344345346347348349350351352353354355391441841 ... Last

• Jump to page: