Moa Hunter
Banned

15704 Likes

Page 678 of 1047 First ... 178578628664665666667668669670671672673674675676677678679680681682683684685686687688689690691692728778 ... Last

• Jump to page:

1. 
   Moa Hunter liked post by On thread : AR15 in rush hour traffic??

   The Police are 100% accountable for allowing gangsterism to get out of control. They seem to prefer showmanship and hubris instead of solid police work and are reaping the rewards of this. Big...

   Liked On: 20-12-2020, 09:25 AM

2. 
   Moa Hunter liked post by Sarvo On thread : Vudoo Gunworks . 22

   Bring this back with it too 156426

   Liked On: 19-12-2020, 11:09 PM

3. 
   Moa Hunter liked post by Micky Duck On thread : Needing - Butcher/ Processing

   we stuffed 15kgs of snags tonight....took us a couple of hours but will be worth it....I have simple recipe that seems to work well for us...and decided to try a couple of kgs of some thing different...

   Liked On: 19-12-2020, 09:26 PM

4. 
   Moa Hunter liked post by bluebaiter222 On thread : Needing - Butcher/ Processing

   Gidday Tian.If you can be arsed trucking from Rolly to Nth Loburn, I,ve got a commercial 3 phase mincer that will do your 21kg in 2.763 seconds.Might cost you some cold ones

   Liked On: 19-12-2020, 09:25 PM

5. 
   Moa Hunter liked post by Micky Duck On thread : Trying something, Eric Cortina method of load development

   also MAYBE worth a crack...can you pinch ring off 2nd set of dies and thread it on UNDERNEATH and work your two rings against each other sandwiching press in between.....the two rings pulling towards...

   Liked On: 19-12-2020, 09:21 PM

6. 
   Moa Hunter liked post by dannyb On thread : Trying something, Eric Cortina method of load development

   It's been a bit of a saga getting this sorted, I desperately need a new press as the thread on my Lee where the die screws in is flogged out and allows slop. It makes it incredibly difficult to seat...

   Liked On: 19-12-2020, 09:21 PM

7. 
   Moa Hunter liked post by Dermastor On thread : Trying something, Eric Cortina method of load development

   Good on ya Danny. I am shooting charge weights and recording velocities tomorrow as I have had to change bullets for my 243 Comp rifle. Then will shoot the best ES load with reducing load lengths on...

   Liked On: 19-12-2020, 09:20 PM

8. 
   Moa Hunter liked post by Scout On thread : MLE/Long Tom to Short Tom

   Hi guys, I ended up with a shortened MLM-MLE / Long Tom fore end & went crazy with my action & spare parts, only roughly fitted up for now. I don't have any full length rifles around any more &...

   Liked On: 18-12-2020, 08:52 PM

9. 
   Moa Hunter liked post by Micky Duck On thread : Trying something, Eric Cortina method of load development

   wow....3000fps with 140grn partition and its grouping inch.......hmmmm methinks I may just have to try some of this H1000...... thats got to put a world of hurt on any deer out to 400 yards with...

   Liked On: 18-12-2020, 08:29 PM

10. 
    Moa Hunter liked post by JaSa On thread : Trying something, Eric Cortina method of load development

    Cool. Looks like a pretty forgiving projectile to load with a big node from 61.5 -63.0gr. 63gr is a good choice in that case. Could even back down to 62.5 if you shoot within a big temperature range...

    Liked On: 18-12-2020, 08:28 PM

11. 
    Moa Hunter liked post by dannyb On thread : Trying something, Eric Cortina method of load development

    I also slapped together a load for nosler 140gn partitions the other day. Got an avg speed of 3000fps and E.S of 16fps with a load the shot just over 1" at 100 yards so I'm pretty happy with that...

    Liked On: 18-12-2020, 08:27 PM

12. 
    Moa Hunter liked post by dannyb On thread : Trying something, Eric Cortina method of load development

    Right after a bit of hiatus this is back on. I did the jam measurements and got 2.858" with 140gn Berger VLDH My mag in the mod 70 allows for 2.843" which just happens to be 15thou off my jam and...

    Liked On: 18-12-2020, 08:26 PM

13. 
    Moa Hunter liked post by Puffin On thread : Trying something, Eric Cortina method of load development

    Just a note on the above, #69: threaded "modified" cases are for the OAL gauge, a measurement that M. Cortina is at pains to emphasize is not required for his method. The stock photo I posted is...

    Liked On: 18-12-2020, 08:23 PM

14. 
    Moa Hunter liked post by Percy Jones On thread : Casings considered ammunition?

    Drill a hole in the side and empty the powder out. Then its no longer a live round. Put a drop of oil on the primer and that will deactivate that also.

    Liked On: 18-12-2020, 07:43 PM

15. 
    Moa Hunter liked post by stagstalker On thread : An evening red deer mission

    Ray has been keen to get out for another hunt for a while and with work going quiet we conducted a check zero on Wednesday morning on his rifle and went bush that afternoon. Turned into a choice...

    Liked On: 18-12-2020, 07:41 PM

Page 678 of 1047 First ... 178578628664665666667668669670671672673674675676677678679680681682683684685686687688689690691692728778 ... Last

• Jump to page: