Moa Hunter
Banned

15704 Likes

Page 783 of 1047 First ... 283683733769770771772773774775776777778779780781782783784785786787788789790791792793794795796797833883 ... Last

• Jump to page:

1. 
   Moa Hunter liked post by Rushy On thread : Fishing tomorrow!

   I think I should come down and live close to you when I am a retired old man. Oh wait ...........

   Liked On: 09-07-2020, 12:48 AM

2. 
   Moa Hunter liked post by veitnamcam On thread : Fishing tomorrow!

   Out straight afetr work this evening.....mirror flat makes it hard to see the banks and channels in the dark. 144466 144467 One large stingray unfortunately but I was still very happy with 19...

   Liked On: 09-07-2020, 12:48 AM

3. 
   Moa Hunter liked post by veitnamcam On thread : Fishing tomorrow!

   Out with the cod masters this morning after a leisurely start, nice weather and I busyed myself with keeping all the smaller cod away from the other rods and other important dutys. 144198 144199...

   Liked On: 09-07-2020, 12:46 AM

4. 
   Moa Hunter liked post by veitnamcam On thread : Fishing tomorrow!

   Well naturally I was out this morning, using my brand new slung 6.5 inch mesh net. A bit of inclement weather sure puts off most of the punters. The only other netter about today is a local who...

   Liked On: 09-07-2020, 12:46 AM

5. 
   Moa Hunter liked post by veitnamcam On thread : Fishing tomorrow!

   Bit bloody windy this morning and a tad wet. 143697 I was the only one out on this side, got 7 and dropped a couple more out of the net. 143698

   Liked On: 09-07-2020, 12:46 AM

6. 
   Moa Hunter liked post by Rushy On thread : Fishing tomorrow!

   Mate tell him the old man on the forum says yes the eat canned corn and also canned peas. Had hours of fun doing it as a young fella up the top of the top end of the Whangamata harbour as the tide...

   Liked On: 09-07-2020, 12:44 AM

7. 
   Moa Hunter liked post by mikee On thread : My Terminator Products 6.5SAUM extracts properly..................Finally

   In fairness to the supplier, I believe the actual "repair's" if you can call them that were carried out by "proper" gunsmiths. What gets me is if it were me in my professional job I would not...

   Liked On: 08-07-2020, 08:47 PM

8. 
   Moa Hunter liked post by Micky Duck On thread : Raincoats. What is the best....

   if your coat cant handle scratchy vege or is down right noisy in the bush...wear it UNDER a polarfleece....light weight polarfleece weighs stuff all when wet as water just runs through it and out the...

   Liked On: 08-07-2020, 03:44 PM

9. 
   Moa Hunter liked post by Steve123 On thread : Raincoats. What is the best....

   I got one of their full blast coats a couple of years back. Its good.

   Liked On: 08-07-2020, 03:44 PM

10. 
    Moa Hunter liked post by The Claw On thread : Raincoats. What is the best....

    If you don't "need" camo then I'd be looking at jackets made for mountaineering etc, especially the heavier duty versions (which are still light compared to most hunting jackets). Good, Lightweight...

    Liked On: 08-07-2020, 03:41 PM

11. 
    Moa Hunter liked post by Nathan F On thread : My Terminator Products 6.5SAUM extracts properly..................Finally

    The CGA applies to any retailer. Only private sellers are excluded.

    Liked On: 08-07-2020, 03:16 PM

12. 
    Moa Hunter liked post by Gibo On thread : My Terminator Products 6.5SAUM extracts properly..................Finally

    Mikee I have a pen that would have sorted that mess! .............too soon? :D 144474

    Liked On: 08-07-2020, 10:37 AM

13. 
    Moa Hunter liked post by mikee On thread : My Terminator Products 6.5SAUM extracts properly..................Finally

    Yes well you would think so, I as a tradesmen stand behind all mine. I can accept shit does happen but its the putting right that counts. in this case I had to put it right myself and at my cost!

    Liked On: 08-07-2020, 10:36 AM

14. 
    Moa Hunter liked post by mikee On thread : My Terminator Products 6.5SAUM extracts properly..................Finally

    Funnilly enough I though that a gunsmith would be all of those things + a machinist.

    Liked On: 08-07-2020, 10:35 AM

15. 
    Moa Hunter liked post by Ryan_Songhurst On thread : My Terminator Products 6.5SAUM extracts properly..................Finally

    Wtf is with the back of that bolt? Looks like its been smashed with a sledgehammer?

    Liked On: 08-07-2020, 10:34 AM

Page 783 of 1047 First ... 283683733769770771772773774775776777778779780781782783784785786787788789790791792793794795796797833883 ... Last

• Jump to page: