Moa Hunter
Banned

15704 Likes

Page 811 of 1047 First ... 311711761797798799800801802803804805806807808809810811812813814815816817818819820821822823824825861911 ... Last

• Jump to page:

1. 
   Moa Hunter liked post by rambo-6mmrem On thread : Federal brass primer pockets??

   Yep I primed some brand new norma 7mmrm brass yesterday the primers took double the pressure to seat than the brand new federal brass

   Liked On: 29-05-2020, 05:55 PM

2. 
   Moa Hunter liked post by Max Headroom On thread : Best value bolt .22 besides Norinco....

   141116 I had a good run with one of these.

   Liked On: 29-05-2020, 01:57 PM

3. 
   Moa Hunter liked post by Micky Duck On thread : .270 Projectiles Lagging Behind

   I got given a part box of bog standard hornady 140grn interlocts...was going to use them for wallabies,rifle shot stupid wee groups with them so they went deer stalking cause rifle was sighted in...

   Liked On: 29-05-2020, 09:09 AM

4. 
   Moa Hunter liked post by Shearer On thread : .270 Projectiles Lagging Behind

   Pretty hot. Wouldn’t have wanted to go over that and it shot well so no need. The ABs do work best at speed though.

   Liked On: 29-05-2020, 08:52 AM

5. 
   Moa Hunter liked post by Micky Duck On thread : Marlin 30-30 setup

   the round shown is an old school silvertip....they came in 150grn for the .308. marlins like shorter rounds than winchesters...projectiles come with crimp groove/cannalure at different places for...

   Liked On: 28-05-2020, 10:06 PM

6. 
   Moa Hunter liked post by dannyb On thread : Marlin 30-30 setup

   I didn't get any of the smithing done but it's 16.5" the mag tube also shortened at the same time so only holds 5 rounds, the trigger also appears to have been fettled. I actually decided against...

   Liked On: 28-05-2020, 10:03 PM

7. 
   Moa Hunter liked post by Cigar On thread : Marlin 30-30 setup

   I'm zeroed at 150m with a 16 inch Winchester Model 94, 1-4x20 scope with pig plex reticle. I also adjust the elevation dial to have a 50m zero with subs.

   Liked On: 28-05-2020, 10:02 PM

8. 
   Moa Hunter liked post by tikka On thread : .270 Projectiles Lagging Behind

   That was also one of the reasons I stopped using 130gr SST on deer from blowing up on the skin. During a roar one of my mates put 5 130gr SST rounds on a stag at 240m then I had to put a 140gr AB to...

   Liked On: 28-05-2020, 08:42 PM

9. 
   Moa Hunter liked post by tikka On thread : .270 Projectiles Lagging Behind

   I really like the performance of the Nosler 150gr LRAB and it worked well both far and near, I adjusted the G1 BC to .611 in my Sako Finnlight. In closer ranges under 400m the 140gr AB was a good...

   Liked On: 28-05-2020, 05:50 PM

10. 
    Moa Hunter liked post by Shearer On thread : .270 Projectiles Lagging Behind

    60gns of N560 in Norma brass. 24" barrel.

    Liked On: 28-05-2020, 05:43 PM

11. 
    Moa Hunter liked post by Freezer On thread : .270 Projectiles Lagging Behind

    270 the new ‘best caliber’ ! I’m still struggling with this but loving shooting mine

    Liked On: 28-05-2020, 04:31 PM

12. 
    Moa Hunter liked post by Shearer On thread : .270 Projectiles Lagging Behind

    I found the 140gn Nosler ABs (MV 3000 fps) to be good killers in my 270win. You've always got your 30cal and 7mm magnums if you want to shoot a loooong way.

    Liked On: 28-05-2020, 02:42 PM

13. 
    Moa Hunter liked post by Bos On thread : .270 Projectiles Lagging Behind

    Was playing round out at farm a couple of weeks ago, just verifying rangefinder and dial-ups, at varying distances.. So rangefinder values dialled in to my VX6 at 200, 300, and 400 yards were spot...

    Liked On: 28-05-2020, 01:56 PM

14. 
    Moa Hunter liked post by Reindeer On thread : Hanwag Boots

    Mate of mine who has a sportshop says 9 of 10 lowas come back, Meindls about the same. Crispi and Grisport have the least returns. Pretty sure he said no Crispis have come back for faults. Scarpa...

    Liked On: 28-05-2020, 08:56 AM

15. 
    Moa Hunter liked post by grandpamac On thread : Federal brass primer pockets??

    Greetings All, Sounds to me that all your loads are too hot. Traditional pressure signs don't show up on cases until pressures are well over max, 70,000 psi or more. Additionally the Federal cases...

    Liked On: 27-05-2020, 03:43 PM

Page 811 of 1047 First ... 311711761797798799800801802803804805806807808809810811812813814815816817818819820821822823824825861911 ... Last

• Jump to page: