Take out the decapping assembly from the die. Fill up the case with cerrosafe. Push the case out (in a vice) with a rod through the decapping assembly hole with a steel rod. I got a case stuck in the...
Liked On: 02-06-2019, 05:46 PM
You will also need a small tow behind sled to carry all the necessary/unnecessary crap that has been suggested.
Liked On: 02-06-2019, 05:42 PM
A warm set of cloths back at your car/truck . Good if you get cold and wet also if you carried out a animal. I keep to the basic's when day hunting but depends where i am hunting and what time of...
Liked On: 02-06-2019, 05:42 PM
one osm an 1 apple is usually all I take for a day most important thing take some dunny paper
Liked On: 02-06-2019, 05:41 PM
7mag, 270wsm, Both manageable recoil with good technique, both capable at that range. More energy, less drift than the same size projectile being pushed slower by the non magnums.
Liked On: 02-06-2019, 05:23 PM
Simple answer, non magnum if 600 was your max then 270 3006 280ai will do the job. Or any of the wsm or magnum cartridges. One thing to consider factory ammo wise is wsm ammo is really expensive...
Liked On: 02-06-2019, 05:23 PM
Had a 3-9 Minox a few years back. May have been just my one, but I found the eye relief a bit close and the eye box a bit narrow at higher magnification. Annoyed me to the point I gave the scope...
Liked On: 01-06-2019, 10:50 PM
Well, I've had a number of T3's and have had an M12 in .308 for some time now, and I won't be reaching for a paddle any time soon. Sounds like Smeagol had an M12 in hand when he molested you.... just...
Liked On: 01-06-2019, 05:23 PM
A 'real deal' Mauser is an M98 and it'll cost anywhere between $8-$50k+ for a new one. The M12 and Tikka T3 fit in the same boat. And that boat has no life rafts; has a giant hole in the hull;...
Liked On: 01-06-2019, 05:23 PM
The flutes on the drill are not as deep as the others. Relieve the flutes as Bobba has shown. Grinding jigs are OK to start out but with practice you will grind drills much faster with good hand...
Liked On: 01-06-2019, 05:20 PM
As above. You need to thin down or sharpen the web using the corner of your grinding wheel. Takes a bit of practice but once you have mastered it you can drill some pretty big holes with no pilot....
Liked On: 01-06-2019, 05:19 PM
the cutting faces need to be 180 degrees from each other (parrallel), they also need to be the same length diagonally and the same angle use the corner of your grinding wheel to take some of the...
Liked On: 01-06-2019, 05:19 PM
No, I mean rode. I was back in the wagon with my 270 and the sheep. The wife drove us, with a Creedmoor on her lap. She lets me ride on the back if I've done all my chores.
Liked On: 01-06-2019, 05:16 PM
Exactly. I was saying the same thing to my neighbour the other day as I rode the horse and cart into town to pick up 2 guineas worth of salted pork and thruppence worth of tobaccy...these 270s are...
Liked On: 01-06-2019, 09:01 AM
Here is the stag i shot early march last year. 112470112471[ATTACH]112473[/ATTACH
Liked On: 01-06-2019, 06:53 AM