mucko
Member

1566 Likes

Page 8 of 105 First 1234567891011121314151617181920212258 ... Last

• Jump to page:

1. 
   mucko liked post by 17brno On thread : bolt failure P14

   Damm might have a bit of a flinch next time you pull the trigger ,glad there are no permanent injures

   Liked On: 26-12-2019, 09:04 AM

2. 
   mucko liked post by jakewire On thread : bolt failure P14

   Really glad your ok mate.

   Liked On: 25-12-2019, 07:20 PM

3. 
   mucko liked post by Woody On thread : bolt failure P14

   mucko. Yep. I found if I full length resized I had case head separation within 5 loads. Went to sizing for headspace off the shoulder which extended case life a bit.

   Liked On: 25-12-2019, 07:20 PM

4. 
   mucko liked post by Woody On thread : bolt failure P14

   mucko. Fair enough. Just one thought. Seems more likely to me that case failed by head separation before the bolt. When you mentioned loose primer pockets I thought to myself that cases may be on the...

   Liked On: 25-12-2019, 04:16 PM

5. 
   mucko liked post by Gapped axe On thread : bolt failure P14

   Sneeze Mike that's bloody close. At least you get Christmas with your family. Get well soon mate and enjoy your break.

   Liked On: 25-12-2019, 03:43 PM

6. 
   mucko liked post by Boaraxa On thread : bolt failure P14

   Crikey , bloody mess mate , buy yourself another rifle for Christmas .

   Liked On: 25-12-2019, 03:43 PM

7. 
   mucko liked post by Woody On thread : bolt failure P14

   mucko. Glad it was no worse mate. Couple of questions. Forgive me please if you have considered these points, which is probable. Trim length of cases compared to chamber length; was there sufficient...

   Liked On: 25-12-2019, 03:27 PM

8. 
   mucko liked post by Sideshow On thread : bolt failure P14

   Man well what ever survived has to go on the next build.....as all the jinxed bits got fecked on that last round so only the good luck bits are left? :thumbsup:

   Liked On: 25-12-2019, 03:26 PM

9. 
   mucko liked post by Tommy On thread : bolt failure P14

   mucko, you win the NZHS award for most improved looks for 2019 though :thumbsup: Jokes aside, glad you kept your sight, that's a fucking biggie

   Liked On: 25-12-2019, 03:25 PM

10. 
    mucko liked post by veitnamcam On thread : bolt failure P14

    I am not a gunsmith. I dont work on guns for a living. However I do do crack repair on a weekly basis, some non critical some extremely critical. Having used penitrant dyes, mag particle...

    Liked On: 25-12-2019, 08:49 AM

11. 
    mucko liked post by Jaco Goosen On thread : bolt failure P14

    Glad your OK - you sure are a lucky man.

    Liked On: 25-12-2019, 08:47 AM

12. 
    mucko liked post by stevodog On thread : bolt failure P14

    That's it mucko, back on the horse:thumbsup:

    Liked On: 24-12-2019, 08:35 PM

13. 
    mucko liked post by gundoc On thread : bolt failure P14

    Any good condition M17 will handle either cartridge well but I made sure I built my own .30/06 long range rifle on a Winchester M17 action. M17 actions by Eddystone, Remington and Winchester were...

    Liked On: 24-12-2019, 08:35 PM

14. 
    mucko liked post by gundoc On thread : bolt failure P14

    Commercial crack testing does work OK but it cannot reveal inherent hardening problems with steel itself, only existing cracks. In this regard the Eddystone actions have always been a precarious...

    Liked On: 24-12-2019, 05:45 PM

15. 
    mucko liked post by csmiffy On thread : bolt failure P14

    mmmmm called my bluff I think. I was going to tap you up for a 303 barrel. that would probably be cheaper 264 win mag......be nice to wack on the 25-303 if that turns to shit

    Liked On: 24-12-2019, 05:45 PM

Page 8 of 105 First 1234567891011121314151617181920212258 ... Last

• Jump to page: