NAKED_GOOSE
Member

345 Likes

Page 3 of 23 First 1234567891011121314151617 ... Last

• Jump to page:

1. 
   NAKED_GOOSE liked post by Micky Duck On thread : Who still makes 0.223" diameter projectiles?

   Buy some factory loads to start with. Fiochi seems to be accurate for everyone who's tried it.you get new brass and get to test rifle with a known good load.

   Liked On: 28-07-2024, 12:58 PM

2. 
   NAKED_GOOSE liked post by Micky Duck On thread : Who still makes 0.223" diameter projectiles?

   Don't shoot at a t shoot at a X that way you can centre reticle north south east n west. If you get me drift. Your cross hairs won't cover the X as that's sticking out in the ne,nw. Se,sw position....

   Liked On: 27-07-2024, 09:05 AM

3. 
   NAKED_GOOSE liked post by rambo-6mmrem On thread : Cast Lead Thread ?

   234716 45-90 with the experimental 542gn groveless

   Liked On: 26-07-2024, 06:46 PM

4. 
   NAKED_GOOSE liked post by Micky Duck On thread : Who still makes 0.223" diameter projectiles?

   Well I would in heartbeat but I'm too plurry far away to do so. A couple of hours to allow him to fire a good accurate rifle sorts out the nut behind butt bit. Someone else to fire his rifle and...

   Liked On: 26-07-2024, 09:08 AM

5. 
   NAKED_GOOSE liked post by Oldbloke On thread : Who still makes 0.223" diameter projectiles?

   Some one needs to help this bloke.

   Liked On: 26-07-2024, 09:08 AM

6. 
   NAKED_GOOSE liked post by Oldbloke On thread : Who still makes 0.223" diameter projectiles?

   I'm a bit far too.

   Liked On: 26-07-2024, 09:00 AM

7. 
   NAKED_GOOSE liked post by Micky Duck On thread : Who still makes 0.223" diameter projectiles?

   I say twelve clicks right

   Liked On: 25-07-2024, 02:57 PM

8. 
   NAKED_GOOSE liked post by 7mm Rem Mag On thread : Who still makes 0.223" diameter projectiles?

   2 or 3 clicks to the right

   Liked On: 25-07-2024, 02:57 PM

9. 
   NAKED_GOOSE liked post by Micky Duck On thread : Who still makes 0.223" diameter projectiles?

   If you are going to continue shooting below fifty yards go and buy an air rifle scope. Parralex set for closer range and they are built tough so should last for years,a much cheaper option for now.

   Liked On: 24-07-2024, 09:10 AM

10. 
    NAKED_GOOSE liked post by HILLBILLYHUNTERS On thread : Gutting and cutting your venison, etc.

    And don't forget the other end , run your knife along the neck full length loosen the throat and cut off where it goes into the body , makes life easy when taking out the vitals .

    Liked On: 23-07-2024, 10:04 AM

11. 
    NAKED_GOOSE liked post by Grey Kiwi On thread : Gutting and cutting your venison, etc.

    Just a thought as there are a lot of new members who are only just now looking to shoot their first game animal. I was lucky in having an elder brother who was a MAF Meat Inspector (MAF now dead and...

    Liked On: 23-07-2024, 09:28 AM

12. 
    NAKED_GOOSE liked post by Crusty On thread : Who still makes 0.223" diameter projectiles?

    Hey Goose, I'm not suggesting you get a parallax adjustable scope. Check your scope for parallax error - on some scopes, especially some cheaper ones, they can have significant parallax errors...

    Liked On: 23-07-2024, 09:18 AM

13. 
    NAKED_GOOSE liked post by Shearer On thread : Tanning some big ole tahr bulls

    Following with interest.

    Liked On: 22-07-2024, 12:58 PM

14. 
    NAKED_GOOSE liked post by Crusty On thread : Who still makes 0.223" diameter projectiles?

    conclusion? I think the Sierra #1385 40gr hp is the go. I think it will be worth trying without resizing down to .221" If I can get a .24" group @25m to translate through to 1" at 100m, I'd be...

    Liked On: 22-07-2024, 09:54 AM

15. 
    NAKED_GOOSE liked post by Crusty On thread : Who still makes 0.223" diameter projectiles?

    255437 Best group at very right at 3 o'clock

    Liked On: 22-07-2024, 09:54 AM

Page 3 of 23 First 1234567891011121314151617 ... Last

• Jump to page: