Nasty Factory Trigger
Member

64 Likes

Page 1 of 5 12345 Last

• Jump to page:

1. 
   Tentman liked post by Nasty Factory Trigger On thread : 80 grain ELDm's in a 1:8 twist .223 Rem.

   Have a looksee at this table for .223 Rem Twist rate vs weight table https://www.everydaymarksman.co/wp-content/uploads/2018/12/224-Stabilization.png

   Liked On: Today, 07:00 AM

2. 
   inglishill liked post by Nasty Factory Trigger On thread : Sub - X load - Case filler needed?

   Loads made up using Hodgdons data - I'll test and report back...

   Liked On: 09-02-2025, 03:45 PM

3. 
   Jhon liked post by Nasty Factory Trigger On thread : Read if you have Hornady Camlock Bullet Puller

   Have one too - done a fair bit of work - I've found that the handle cam lobes wear or rather distort where it interfaces with said concave bearing surface... flaring the material out - cleaned up...

   Liked On: 04-09-2024, 12:30 PM

4. 
   short swede liked post by Nasty Factory Trigger On thread : What little pesties did you bowl over today?

   Hardly worthy of the mention, though adding to the list anyway... Just the one hare - yep just one... Saturday night was a real struggle with ground fog greeting me as I drove up the cattle...

   Liked On: 07-05-2024, 05:41 PM

5. 
   Dama dama liked post by Nasty Factory Trigger On thread : What little pesties did you bowl over today?

   Hardly worthy of the mention, though adding to the list anyway... Just the one hare - yep just one... Saturday night was a real struggle with ground fog greeting me as I drove up the cattle...

   Liked On: 06-05-2024, 11:38 AM

6. 
   kristopher liked post by Nasty Factory Trigger On thread : Gun safe question

   Plus one for selling the A-cat 2-3mm flimsy thing... went and bought a lonely E-cat 6mm that was long-sitting on a salesroom floor - this was even after Jacinda took E cat away... Yep, def can't...

   Liked On: 24-04-2024, 05:52 AM

7. 
   Micky Duck liked post by Nasty Factory Trigger On thread : Hornady 62 gr 223 proj not grouping

   Good point MD - 1-8 Howa... shoots the 60 VMax fine though..

   Liked On: 14-08-2023, 08:39 PM

8. 
   Micky Duck liked post by Nasty Factory Trigger On thread : Variations of 'same projectile' Hornady 150gr SP Interlock

   Referring back the photos, the early version measured the 0.508 inch to ogive, whereas the later and current proj measured the 0.47 inch ogive to base... offering less bearing surface ... must be...

   Liked On: 25-07-2023, 09:42 PM

9. 
   Micky Duck liked post by Nasty Factory Trigger On thread : Variations of 'same projectile' Hornady 150gr SP Interlock

   Yes, instantly checked that!! were a few grains off 150, though 150gr they were...

   Liked On: 25-07-2023, 09:35 PM

10. 
    veitnamcam liked post by Nasty Factory Trigger On thread : Variations of 'same projectile' Hornady 150gr SP Interlock

    I must admit, this was an old box bought when I bought my 308 eons ago, and rather than keep proj separately, Ive thrown 'same' Interlocks in the same box - foolishly believing there would be no...

    Liked On: 25-07-2023, 09:21 PM

11. 
    zimmer liked post by Nasty Factory Trigger On thread : Variations of 'same projectile' Hornady 150gr SP Interlock

    So, while casually reloading, I do check everything, from powder throw on scales to final seating depth check with comparitor and verniers - hello, whay am I seeing 2 variations in seating depth...

    Liked On: 25-07-2023, 08:40 PM

12. 
    Micky Duck liked post by Nasty Factory Trigger On thread : Variations of 'same projectile' Hornady 150gr SP Interlock

    I must admit, this was an old box bought when I bought my 308 eons ago, and rather than keep proj separately, Ive thrown 'same' Interlocks in the same box - foolishly believing there would be no...

    Liked On: 25-07-2023, 05:51 PM

13. 
    rupert liked post by Nasty Factory Trigger On thread : Variations of 'same projectile' Hornady 150gr SP Interlock

    So, while casually reloading, I do check everything, from powder throw on scales to final seating depth check with comparitor and verniers - hello, whay am I seeing 2 variations in seating depth...

    Liked On: 25-07-2023, 05:36 PM

14. 
    Nesika liked post by Nasty Factory Trigger On thread : Question - 850nm or 940nm IR torch?

    It suits my needs - I for one, did not want to commit a rifle to Night duties only, though understand they can be used during the day as well - moreso that I can sight my rifles 17 HMR / 223 Rem /...

    Liked On: 24-06-2023, 07:06 PM

15. 
    viper liked post by Nasty Factory Trigger On thread : What little pesties did you bowl over today?

    218139 263 yards with the 17 HMR... Loves the A17 ammo :)

    Liked On: 13-03-2023, 09:51 AM

Page 1 of 5 12345 Last

• Jump to page: