No.3
Member

2531 Likes

Page 133 of 169 First ... 3383119120121122123124125126127128129130131132133134135136137138139140141142143144145146147 ... Last

• Jump to page:

1. 
   Micky Duck liked post by No.3 On thread : show us your chainsaws

   Yikes. That's not approved by your average lady is it... Got to the bottom of that weird revving up issue on the ms460 - impulse line at the crank case end had gone very slightly hard. It wasn't...

   Liked On: 03-02-2023, 12:58 PM

2. 
   Micky Duck liked post by No.3 On thread : show us your chainsaws

   Ha yeah, bloody Ironbark timber. That stuff was brutal on chains, I went through three on one pile once. Not recoverable, teeth tips were pealed up and back and chains were written off! Funny with...

   Liked On: 03-02-2023, 12:57 PM

3. 
   Micky Duck liked post by No.3 On thread : show us your chainsaws

   Yep, the good old rapeseed oil. Twice the price for half as good! One thing about using hydraulic saws under water is the water effectively lubricates the bar to a certain extent so you can get...

   Liked On: 03-02-2023, 12:56 PM

4. 
   7mmsaum liked post by No.3 On thread : show us your chainsaws

   Yikes. That's not approved by your average lady is it... Got to the bottom of that weird revving up issue on the ms460 - impulse line at the crank case end had gone very slightly hard. It wasn't...

   Liked On: 03-02-2023, 05:42 AM

5. 
   Hermitage liked post by No.3 On thread : How do these Warne Vertical Rings work?

   Once adjusted and locked on the recoil plate is captive on dovetails, can't go anywhere. Note this is the 4-screw maxima version I'm referring to no the 2-screw which uses the screw as the recoil...

   Liked On: 02-02-2023, 06:14 PM

6. 
   Puffin liked post by No.3 On thread : How do these Warne Vertical Rings work?

   Used them on many many scopes, including lightweight thin alloy tube ones. As said, torque settings are vital on these and start at the bottom screws and work up. Having said that, with their...

   Liked On: 02-02-2023, 09:28 AM

7. 
   Hermitage liked post by No.3 On thread : How do these Warne Vertical Rings work?

   Used them on many many scopes, including lightweight thin alloy tube ones. As said, torque settings are vital on these and start at the bottom screws and work up. Having said that, with their...

   Liked On: 01-02-2023, 10:03 PM

8. 
   paremata liked post by No.3 On thread : show us your chainsaws

   Ha yeah, bloody Ironbark timber. That stuff was brutal on chains, I went through three on one pile once. Not recoverable, teeth tips were pealed up and back and chains were written off! Funny with...

   Liked On: 01-02-2023, 09:29 PM

9. 
   Micky Duck liked post by No.3 On thread : show us your chainsaws

   Yep a basic gear oil. Nice and sticky enough tack to stick to gears circulating will make for a very effective bar lube. Only thing with that is it has a fairly robust additive pack that is quite...

   Liked On: 01-02-2023, 03:22 PM

10. 
    Micky Duck liked post by No.3 On thread : show us your chainsaws

    Probably work. Just can't be arsed running two types of bar oil... Its not emptying the tank before the fuel runs out, so acceptable in use just makes a bit of a puddle under the clutch cover. On...

    Liked On: 01-02-2023, 02:04 PM

11. 
    Micky Duck liked post by No.3 On thread : show us your chainsaws

    Some can get away with this, some it doesn't provide much. Generally the newer split case 'professional' series saws do this, but some of them don't. I have a MS460 I've just rebuilt with the...

    Liked On: 01-02-2023, 10:15 AM

12. 
    Micky Duck liked post by No.3 On thread : Dumb question about shooting

    If you are "going all around" the target at increased range, go back to paper and shoot a decent group at each range. Assess each group at each range for patterns of impact - looking to isolate...

    Liked On: 01-02-2023, 09:43 AM

13. 
    MCCPRO liked post by No.3 On thread : Helicopter pilot gratuity

    Well, that counts me out for travelling to the US - lost my tip to a date with the surgeon.

    Liked On: 01-02-2023, 08:37 AM

14. 
    distant stalker liked post by No.3 On thread : Dumb question about shooting

    If you are "going all around" the target at increased range, go back to paper and shoot a decent group at each range. Assess each group at each range for patterns of impact - looking to isolate...

    Liked On: 31-01-2023, 07:55 PM

15. 
    Rusky liked post by No.3 On thread : Dumb question about shooting

    If you are "going all around" the target at increased range, go back to paper and shoot a decent group at each range. Assess each group at each range for patterns of impact - looking to isolate...

    Liked On: 31-01-2023, 01:49 PM

Page 133 of 169 First ... 3383119120121122123124125126127128129130131132133134135136137138139140141142143144145146147 ... Last

• Jump to page: