No.3
Member

2526 Likes

Page 158 of 169 First ... 58108144145146147148149150151152153154155156157158159160161162163164165166167168169 Last

• Jump to page:

1. 
   Gibo liked post by No.3 On thread : Machete

   Gerber? Expensive but I'm told they tend to keep their edge OK. Otherwise you could try what the Air Cav did in Vietnam and run a line of det cord down. Not exactly the most neighbour friendly...

   Liked On: 25-08-2022, 06:52 PM

2. 
   Tahr liked post by No.3 On thread : Silky saws

   Ahh that looks a little better than the bow saws I have here, same blade tech but those are slightly smaller with a more rigid handle. Mine are more like a cross between the Jack jobbie and what you...

   Liked On: 25-08-2022, 06:17 PM

3. 
   Maxx liked post by No.3 On thread : Silky saws

   F180 is my one for what it's worth... https://silkystore.co.nz/products/f180-with-tabs

   Liked On: 25-08-2022, 12:51 PM

4. 
   Puffin liked post by No.3 On thread : Silky saws

   F180 is my one for what it's worth... https://silkystore.co.nz/products/f180-with-tabs

   Liked On: 25-08-2022, 12:43 AM

5. 
   RV1 liked post by No.3 On thread : Silky saws

   I have a Silky folder, had it for something like 20 years now and on the 2nd blade. I have no idea what the current equivalent model is now but it's a brilliant saw, destroyed the first blade...

   Liked On: 24-08-2022, 03:07 PM

6. 
   RV1 liked post by No.3 On thread : Silky saws

   F180 is my one for what it's worth... https://silkystore.co.nz/products/f180-with-tabs

   Liked On: 24-08-2022, 03:07 PM

7. 
   Ftx325 liked post by No.3 On thread : Silky saws

   F180 is my one for what it's worth... https://silkystore.co.nz/products/f180-with-tabs

   Liked On: 24-08-2022, 10:15 AM

8. 
   Shootm liked post by No.3 On thread : Silky saws

   F180 is my one for what it's worth... https://silkystore.co.nz/products/f180-with-tabs

   Liked On: 23-08-2022, 11:30 PM

9. 
   Micky Duck liked post by No.3 On thread : Silky saws

   I have a Silky folder, had it for something like 20 years now and on the 2nd blade. I have no idea what the current equivalent model is now but it's a brilliant saw, destroyed the first blade...

   Liked On: 23-08-2022, 09:56 PM

10. 
    rewa liked post by No.3 On thread : Quality "everlasting" .410 shells

    Try gasket cork from an engineering outfit, it's more flexible and better for cutting...

    Liked On: 21-08-2022, 02:32 PM

11. 
    timattalon liked post by No.3 On thread : Panelbeater narrowly avoids Armageddon

    Ha didn't find anything on this and chucked the link into the off topic section. I reckon a load of crap, used to open old unwanted shotgun shells with a grinder to recover the lead for sinkers and...

    Liked On: 20-08-2022, 02:27 AM

12. 
    300CALMAN liked post by No.3 On thread : Panelbeater narrowly avoids Armageddon

    Ha didn't find anything on this and chucked the link into the off topic section. I reckon a load of crap, used to open old unwanted shotgun shells with a grinder to recover the lead for sinkers and...

    Liked On: 19-08-2022, 11:07 PM

13. 
    veitnamcam liked post by No.3 On thread : Panelbeater narrowly avoids Armageddon

    Ha didn't find anything on this and chucked the link into the off topic section. I reckon a load of crap, used to open old unwanted shotgun shells with a grinder to recover the lead for sinkers and...

    Liked On: 19-08-2022, 09:52 PM

14. 
    Micky Duck liked post by No.3 On thread : Panelbeater narrowly avoids Armageddon

    Ha didn't find anything on this and chucked the link into the off topic section. I reckon a load of crap, used to open old unwanted shotgun shells with a grinder to recover the lead for sinkers and...

    Liked On: 19-08-2022, 07:00 PM

15. 
    rewa liked post by No.3 On thread : Panelbeater narrowly avoids Armageddon

    Ha didn't find anything on this and chucked the link into the off topic section. I reckon a load of crap, used to open old unwanted shotgun shells with a grinder to recover the lead for sinkers and...

    Liked On: 19-08-2022, 10:17 AM

Page 158 of 169 First ... 58108144145146147148149150151152153154155156157158159160161162163164165166167168169 Last

• Jump to page: