No.3
Member

2519 Likes

Page 20 of 168 First ... 67891011121314151617181920212223242526272829303132333470120 ... Last

• Jump to page:

1. 
   earplay liked post by No.3 On thread : Budget barrel cooler

   Hey hey hey - where are the cable ties and no8 wire?????????

   Liked On: 14-12-2024, 01:05 PM

2. 
   BRADS liked post by No.3 On thread : Rip off of the week

   That really annoys me - not the people having a crack themselves as that is the kiwi way and it's how ya upskill and learn. It's the bagging of the pros just because you don't like paying to get the...

   Liked On: 14-12-2024, 10:11 AM

3. 
   7mm tragic liked post by No.3 On thread : ZKK-600 7x57 Hard to chamber

   Nah don't ream yet. Can you put up photo's of the outside edge of each bolt lug, the contact face of each bolt lug and also the third emergency lug and the cocking area of the back of the bolt...

   Liked On: 14-12-2024, 08:38 AM

4. 
   Barry the hunter liked post by No.3 On thread : ZKK-600 7x57 Hard to chamber

   Nah don't ream yet. Can you put up photo's of the outside edge of each bolt lug, the contact face of each bolt lug and also the third emergency lug and the cocking area of the back of the bolt...

   Liked On: 13-12-2024, 02:42 PM

5. 
   Micky Duck liked post by No.3 On thread : Rip off of the week

   Those water pumps aren't even that difficult, a fair bit of farting about getting to them though. Those bearings in the idler pulleys are a classic, I've done a heap on marine engines and used...

   Liked On: 12-12-2024, 11:28 PM

6. 
   witchcraft liked post by No.3 On thread : Rip off of the week

   Those water pumps aren't even that difficult, a fair bit of farting about getting to them though. Those bearings in the idler pulleys are a classic, I've done a heap on marine engines and used...

   Liked On: 12-12-2024, 04:47 PM

7. 
   kristopher liked post by No.3 On thread : Rip off of the week

   Those water pumps aren't even that difficult, a fair bit of farting about getting to them though. Those bearings in the idler pulleys are a classic, I've done a heap on marine engines and used...

   Liked On: 12-12-2024, 05:30 AM

8. 
   Billymavs liked post by No.3 On thread : ZKK-600 7x57 Hard to chamber

   Is the bolt assembled correctly and it works fine without a round trying to chamber?

   Liked On: 11-12-2024, 10:52 PM

9. 
   Kiwimaverick liked post by No.3 On thread : Knife restoration

   It's going to be fine once it's cleaned up - sometimes the flap discs or sanding discs are the way forward and other times you really need to get a bit more heavy to get to the bottom of the pitting....

   Liked On: 11-12-2024, 10:16 AM

10. 
    m101a1 liked post by No.3 On thread : 1998 nissan mistral TDi problem

    Although to be fair there is a sump low point in the tank to collect the heavy crap and as long as you aren't culturing living things in your tank you should be fine. I have had a couple of...

    Liked On: 08-12-2024, 07:56 PM

11. 
    Carbine liked post by No.3 On thread : 1998 nissan mistral TDi problem

    Although to be fair there is a sump low point in the tank to collect the heavy crap and as long as you aren't culturing living things in your tank you should be fine. I have had a couple of...

    Liked On: 08-12-2024, 06:02 PM

12. 
    BSA270 liked post by No.3 On thread : A bitter lesson on technique!

    Good when it's a simple fix. The number of times I have seen people shooting off a rest, take two or three shots normally then the next with the barrel on the rest and not the foreend... Simple...

    Liked On: 06-12-2024, 12:44 PM

13. 
    Localman liked post by No.3 On thread : Luxury Caravan

    Empty the water tank haha... That and transfer 40Kg of kitchen and pantry to the tow vehicle. Mates one was OK on the way to the camp ground, was weighed on the way home at a checkpoint and...

    Liked On: 06-12-2024, 09:48 AM

14. 
    caberslash liked post by No.3 On thread : "New" scopes.

    The other end of this is outfits getting the components made to spec all over the planet and then shipped to a place for assembly. You see a lot of scopes with German glass, Asian made mechanical...

    Liked On: 06-12-2024, 04:37 AM

15. 
    littlemorepork liked post by No.3 On thread : My 9.3x62...

    I'm not sure you're quite understanding the point some of us are trying to make - it's not a smartarse "pussy shooter" thing it's just the dynamics of the big guns and how the stock design can make...

    Liked On: 05-12-2024, 12:48 AM

Page 20 of 168 First ... 67891011121314151617181920212223242526272829303132333470120 ... Last

• Jump to page: