No.3
Member

2527 Likes

Page 42 of 169 First ... 282930313233343536373839404142434445464748495051525354555692142 ... Last

• Jump to page:

1. 
   Jhon liked post by No.3 On thread : Read if you have Hornady Camlock Bullet Puller

   The pliers thing might be OK for longer bullets that aren't crimped (and I have done it) but on anything with a crimp, sealed or softer jacketed the pliers will write the pills off. The collets have...

   Liked On: 24-08-2024, 03:23 PM

2. 
   Micky Duck liked post by No.3 On thread : 22 mag for goats?

   Are you suggesting that a semi-auto is more effective at culling animals? Wow, brave move (but completely accurate). As far as the goats, be aware that you got four of the five of the only mob...

   Liked On: 24-08-2024, 12:53 PM

3. 
   Barry the hunter liked post by No.3 On thread : 22 mag for goats?

   Are you suggesting that a semi-auto is more effective at culling animals? Wow, brave move (but completely accurate). As far as the goats, be aware that you got four of the five of the only mob...

   Liked On: 24-08-2024, 12:12 PM

4. 
   veitnamcam liked post by No.3 On thread : Prados

   Yeah, but nah not in this case. I don't know any more but I would put forward the guess that the pilot might not have used the correct techniques just quietly. The mate wasn't that flattering when...

   Liked On: 23-08-2024, 06:59 PM

5. 
   Finnwolf liked post by No.3 On thread : Toasti - The Crispy Cruiser

   Good point, the foam is a chlorinated product so once it's burned it will keep releasing chlorine and in the wrong conditions hydrogen cyanide... Fairly nasty.

   Liked On: 22-08-2024, 08:08 AM

6. 
   Jhon liked post by No.3 On thread : 7mm-08 reloads extraction issue - thoughts please

   Small base dies if you can get them, but the other issue might be a good annealing of the brass. As stupid as it sounds, that might be a cause of this. I had it in an old zkw465 .22 Hornet - hardly...

   Liked On: 21-08-2024, 10:33 PM

7. 
   cambo liked post by No.3 On thread : Toasti - The Crispy Cruiser

   Good point, the foam is a chlorinated product so once it's burned it will keep releasing chlorine and in the wrong conditions hydrogen cyanide... Fairly nasty.

   Liked On: 21-08-2024, 10:31 PM

8. 
   Trout liked post by No.3 On thread : Toasti - The Crispy Cruiser

   Good point, the foam is a chlorinated product so once it's burned it will keep releasing chlorine and in the wrong conditions hydrogen cyanide... Fairly nasty.

   Liked On: 21-08-2024, 05:44 PM

9. 
   Muttonguts liked post by No.3 On thread : Useing the firearms register

   If it is focused on public and firearms user safety, easing the operational burden on the volunteers that run the clubs and range committees and allows range officers greater protection to do their...

   Liked On: 21-08-2024, 01:13 PM

10. 
    Micky Duck liked post by No.3 On thread : 223 - unusual results

    And fark me, that thing was a noisy, uncomfortable, disruptive, smelly, smokey, pumice blasting pig of a thing at the very best of times. Usually the BOSS system was worse in reality. What a prick...

    Liked On: 20-08-2024, 10:31 AM

11. 
    Oldbloke liked post by No.3 On thread : Reloading 22 Hornet (The Original) – Optimal Canada Goose Load

    I dunno about the dishwasher stuffing the temper of a knife - after all cutting up a freshly cooked chunk of meat is hotter than the dishwasher and knives handle that fine... I think the knife in...

    Liked On: 19-08-2024, 08:23 PM

12. 
    Micky Duck liked post by No.3 On thread : White River Primers - Any misfire issues?

    Ahh - I found my priming improved a LOT with going to a hand primer, could feel and judge when the primer cup was properly seated. For some reason I was getting the odd proud and tall one out of the...

    Liked On: 19-08-2024, 08:03 PM

13. 
    Micky Duck liked post by No.3 On thread : Is this a Kelly axe

    Wa wa wa haha...

    Liked On: 19-08-2024, 01:27 PM

14. 
    hunter Al.7mm08 liked post by No.3 On thread : Is this a Kelly axe

    Apparently these were the ones exported to Aussie before Kelly entered the agreement to have them locally produced in Aussie. Hence the "Made in Canada" on one side, and the World's Finest Kelly...

    Liked On: 19-08-2024, 11:11 AM

15. 
    Micky Duck liked post by No.3 On thread : Is this a Kelly axe

    Apparently these were the ones exported to Aussie before Kelly entered the agreement to have them locally produced in Aussie. Hence the "Made in Canada" on one side, and the World's Finest Kelly...

    Liked On: 19-08-2024, 12:14 AM

Page 42 of 169 First ... 282930313233343536373839404142434445464748495051525354555692142 ... Last

• Jump to page: