onlyhsh
Member

42 Likes

Page 2 of 3 First 123 Last

• Jump to page:

1. 
   onlyhsh liked post by Roarless20 On thread : Tight chamber and marks on projectile

   In your pics it appears that the neck isn't sized all the way down and the case shoulder looks rounded as though it hasn't been sized back. Wind your sizing die in further to bump the shoulder back...

   Liked On: 09-07-2024, 02:53 PM

2. 
   onlyhsh liked post by zimmer On thread : 6.5 Grendel load trouble shoot

   I'm a Mitutoyo man myself which comes about from my trade background. The Hornady will most likely be a Chinaman. I also have a Chinese digital calliper and it works perfectly OK. It's the one I...

   Liked On: 18-01-2022, 01:36 PM

3. 
   onlyhsh liked post by Pommy On thread : 6.5 Grendel load trouble shoot

   Yep, Hornady calliper is fine. Could your powder have gone bad? How old is it? How's it been stored? Has it been left open at any point? The electronic scales are shite and drift all the time but...

   Liked On: 18-01-2022, 01:35 PM

4. 
   onlyhsh liked post by Pete_D On thread : 6.5 Grendel load trouble shoot

   We load a very similar load but an 123gr. SST and 8208. Our load is 27.7g and its not compressed but very close, anything over 28g and you could defiantly hear faint crunching when seating the...

   Liked On: 18-01-2022, 09:52 AM

5. 
   onlyhsh liked post by zimmer On thread : 6.5 Grendel load trouble shoot

   Yep. Over and over I've pointed this out to new hand loaders. Get a mechanical beam scale. The el cheapo digital with strain gauge innards will let you down with zero drift. And something with a...

   Liked On: 18-01-2022, 09:51 AM

6. 
   onlyhsh liked post by Shamus_ On thread : 6.5 Grendel load trouble shoot

   A decent beam scale might be a more reliable option ...

   Liked On: 18-01-2022, 09:51 AM

7. 
   onlyhsh liked post by keengunNic On thread : 6.5 Grendel load trouble shoot

   Never was able to get good results with my 1500 g2, ended up going balls deep on an autotrickler setup and fuck, what a setup. Reloading is not for the money saver. Gordons Reloading tool is bloody...

   Liked On: 18-01-2022, 09:51 AM

8. 
   onlyhsh liked post by zimmer On thread : 6.5 Grendel load trouble shoot

   Gordon's tool does the sameand it's free to download.

   Liked On: 14-01-2022, 09:03 PM

9. 
   onlyhsh liked post by Marty Henry On thread : Suppressor and load dev

   I think Jhon has the right idea. I feel that for a hunting rifle the idea of developing an ideal load is actually pretty pointless if anything you chuck down the barrel prints about 1 moa anyhow....

   Liked On: 07-11-2021, 11:59 AM

10. 
    onlyhsh liked post by chainsaw On thread : Suppressor and load dev

    I’ve done a lot of load dev for a heap of different rifles and calibres over the years. Yet to find one where the accuracy node and POI is much different with or with out suppressor. One point I have...

    Liked On: 07-11-2021, 11:53 AM

11. 
    onlyhsh liked post by Mooseman On thread : Suppressor and load dev

    I have just had one fitted to my 300 win Mag , at 25 yds it was 2 inches low and an inch right with suppressor on using the load it was sighted in for without the suppressor. Point of impact is quite...

    Liked On: 07-11-2021, 11:51 AM

12. 
    onlyhsh liked post by Magnetite On thread : Suppressor and load dev

    I haven’t done load development unsuppressed, but I have shot the load without it. The harmonics are definitely different and the POI shift was huge, ~10cm at 100m.

    Liked On: 07-11-2021, 11:51 AM

13. 
    onlyhsh liked post by Jhon On thread : Suppressor and load dev

    There may be good reasons to hold off, especially if its just for a short while until a suppressor arrives. To be fair, the difference in POI between suppressor and no supressor is likely to be...

    Liked On: 07-11-2021, 11:50 AM

14. 
    onlyhsh liked post by CBH Australia On thread : Suppressor and load dev

    Move to Australia, no suppressors allowed. Problem solved. I think you could do the development with it on. I believe it will affect harmonics. That is it will change the point of impact with it...

    Liked On: 07-11-2021, 12:34 AM

15. 
    onlyhsh liked post by 257weatherby On thread : Suppressor and load dev

    Get your barrels threaded the same and use one suppressor made for the larger diameter pill, instead of two. Just need to have a rear bush to suit each barrel.

    Liked On: 07-11-2021, 12:33 AM

Page 2 of 3 First 123 Last

• Jump to page: