outlander
Member

4466 Likes

Page 146 of 298 First ... 4696132133134135136137138139140141142143144145146147148149150151152153154155156157158159160196246 ... Last

• Jump to page:

1. 
   outlander liked post by Sarvo On thread : Had to be done

   Before anyone jumps down my throat - in no way do I condone this clowning idiocy But I think some of you must have lead a fairly sheltered life to not know this sort of crap has been around since...

   Liked On: 06-03-2021, 12:25 PM

2. 
   outlander liked post by bumblefoot On thread : Had to be done

   hotbarrels I wouldn't put the life savings on it. I don't think the cops raided the gang leader who admitted on tv that he wasn't handing any of his guns in because he needed them for "self...

   Liked On: 06-03-2021, 12:24 PM

3. 
   outlander liked post by Woody On thread : Bullet pulling related question

   Tap the pulled brass smartly on its side on the bench. This usually dislodges any stuck kernels.

   Liked On: 06-03-2021, 11:11 AM

4. 
   outlander liked post by Cordite On thread : Bullet pulling related question

   Tim Dicko A small, stiff paint brush chucked up in a power drill. You CAN of course also just clean the holes by hand using a watchmakers screwdriver of right size. Unless you use a hammer, this...

   Liked On: 06-03-2021, 11:10 AM

5. 
   outlander liked post by shooternz On thread : Bullet pulling related question

   A few kernels of powder will not make the slightest bit of difference in a load of powder for a 260 it is well within the margin of error of your powder weighing device, And your neck tension is...

   Liked On: 06-03-2021, 11:10 AM

6. 
   outlander liked post by JaSa On thread : Bullet pulling related question

   Neck tension will be all over the show. Best to resize...

   Liked On: 06-03-2021, 11:09 AM

7. 
   outlander liked post by Ftx325 On thread : Bike Porn - Regardless of the motor, Show off your "two wheeled" beasties

   Ya don't need to apologise outlander... I know you were joking....i'm just winding you up mate All good :thumbsup:

   Liked On: 06-03-2021, 11:01 AM

8. 
   outlander liked post by veitnamcam On thread : Bike Porn - Regardless of the motor, Show off your "two wheeled" beasties

   Is it easy to wheelie?

   Liked On: 05-03-2021, 03:37 PM

9. 
   outlander liked post by Ftx325 On thread : Bike Porn - Regardless of the motor, Show off your "two wheeled" beasties

   I cannot confirm or deny for fear of incriminating myself .... :cool:

   Liked On: 05-03-2021, 03:36 PM

10. 
    outlander liked post by Nathan F On thread : Had to be done

    https://www.nzhuntingandshooting.co.nz/f12/ok-kawekas-where-week-go-65793/

    Liked On: 05-03-2021, 09:56 AM

11. 
    outlander liked post by XR500 On thread : Ok, kawekas... where, for a week... and go.

    ...but its not hunting. Its shooting. And therein lies the difference in attitude I guess.

    Liked On: 05-03-2021, 09:49 AM

12. 
    outlander liked post by Grasshoppa On thread : Had to be done

    Pack of dickheads the lot of them, there's at least one forum member amongst them, f*&ken clueless

    Liked On: 05-03-2021, 09:43 AM

13. 
    outlander liked post by ariki On thread : Had to be done

    Had the same thing happen at Clements a month ago took girlfriend and step son down for a hunt. And an hour after daylight a holes start shooting up Clements Clearing. Nice night camping in bush...

    Liked On: 05-03-2021, 09:42 AM

14. 
    outlander liked post by outdoorlad On thread : Had to be done

    This shit is exactly why hunters get a bad wrap, not that I’d call them hunters.

    Liked On: 04-03-2021, 07:59 PM

15. 
    outlander liked post by bigbear On thread : Had to be done

    Cant be hard to work out who this guy is shoots a Wairarapa Clay Target Club and his mate. Over the last couple months i have watched a bit of u tube to keep me insane from been stuck at home, and...

    Liked On: 04-03-2021, 07:59 PM

Page 146 of 298 First ... 4696132133134135136137138139140141142143144145146147148149150151152153154155156157158159160196246 ... Last

• Jump to page: