PaulNZ
Member

393 Likes

Page 21 of 27 First ... 789101112131415161718192021222324252627 Last

• Jump to page:

1. 
   Klhari liked post by PaulNZ On thread : Walnut Stock Build

   Thanks for the responses all. So looking through the gun cabinet my Anschutz 1717 .17hmr was chosen as the restocking victim candidate. I thought I had a picture of it in the original stock but...

   Liked On: 09-04-2020, 12:23 AM

2. 
   Tommy liked post by PaulNZ On thread : Walnut Stock Build

   One more post and this’ll be up to date with where I’m actually at. If I was writing this chronologically, there should actually be a post in between thinking the pattern stock was done and then...

   Liked On: 08-04-2020, 01:10 PM

3. 
   berg243 liked post by PaulNZ On thread : Walnut Stock Build

   I wasn’t going to make this thread until I was a bit further along, however perhaps with the current lockdown now’s a good time. I know I appreciate reading similar threads created by other members –...

   Liked On: 07-04-2020, 03:26 PM

4. 
   Bryan liked post by PaulNZ On thread : Walnut Stock Build

   One more post and this’ll be up to date with where I’m actually at. If I was writing this chronologically, there should actually be a post in between thinking the pattern stock was done and then...

   Liked On: 06-04-2020, 11:24 PM

5. 
   chainsaw liked post by PaulNZ On thread : Walnut Stock Build

   One more post and this’ll be up to date with where I’m actually at. If I was writing this chronologically, there should actually be a post in between thinking the pattern stock was done and then...

   Liked On: 06-04-2020, 10:22 PM

6. 
   Moa Hunter liked post by PaulNZ On thread : Walnut Stock Build

   Thanks for all the comments and encouragement everyone. Good point. I don't think I've shot with a Sako Forester, but I did use a borrowed Alpine .270 for a few months (English, based on an...

   Liked On: 06-04-2020, 09:39 PM

7. 
   rupert liked post by PaulNZ On thread : Walnut Stock Build

   One more post and this’ll be up to date with where I’m actually at. If I was writing this chronologically, there should actually be a post in between thinking the pattern stock was done and then...

   Liked On: 06-04-2020, 01:50 PM

8. 
   paddygonebush liked post by PaulNZ On thread : Walnut Stock Build

   One more post and this’ll be up to date with where I’m actually at. If I was writing this chronologically, there should actually be a post in between thinking the pattern stock was done and then...

   Liked On: 06-04-2020, 12:21 PM

9. 
   Moa Hunter liked post by PaulNZ On thread : Walnut Stock Build

   One more post and this’ll be up to date with where I’m actually at. If I was writing this chronologically, there should actually be a post in between thinking the pattern stock was done and then...

   Liked On: 06-04-2020, 10:30 AM

10. 
    Moa Hunter liked post by PaulNZ On thread : Walnut Stock Build

    So some of the changes I made to the stock at this point were to reduce LOP by ¼”, flatten off the palm swell slightly, and deepen and extend the comb fluting. All easily done. But I also couldn’t...

    Liked On: 06-04-2020, 10:28 AM

11. 
    Moa Hunter liked post by PaulNZ On thread : Walnut Stock Build

    Another few snapshots from the milling for your interest. Note that these are all with the wood still wet – the colour did change considerably after drying. https://i.imgur.com/uGWBeQB.jpg ...

    Liked On: 06-04-2020, 10:26 AM

12. 
    Joe_90 liked post by PaulNZ On thread : Walnut Stock Build

    One more post and this’ll be up to date with where I’m actually at. If I was writing this chronologically, there should actually be a post in between thinking the pattern stock was done and then...

    Liked On: 06-04-2020, 10:21 AM

13. 
    Mathias liked post by PaulNZ On thread : Walnut Stock Build

    One more post and this’ll be up to date with where I’m actually at. If I was writing this chronologically, there should actually be a post in between thinking the pattern stock was done and then...

    Liked On: 06-04-2020, 09:45 AM

14. 
    FRST liked post by PaulNZ On thread : Walnut Stock Build

    Thanks for the responses all. So looking through the gun cabinet my Anschutz 1717 .17hmr was chosen as the restocking victim candidate. I thought I had a picture of it in the original stock but...

    Liked On: 06-04-2020, 09:41 AM

15. 
    Steelisreal liked post by PaulNZ On thread : Walnut Stock Build

    So some of the changes I made to the stock at this point were to reduce LOP by ¼”, flatten off the palm swell slightly, and deepen and extend the comb fluting. All easily done. But I also couldn’t...

    Liked On: 06-04-2020, 09:40 AM

Page 21 of 27 First ... 789101112131415161718192021222324252627 Last

• Jump to page: