PaulNZ
Member

393 Likes

Page 22 of 27 First ... 89101112131415161718192021222324252627 Last

• Jump to page:

1. 
   Steelisreal liked post by PaulNZ On thread : Walnut Stock Build

   Another few snapshots from the milling for your interest. Note that these are all with the wood still wet – the colour did change considerably after drying. https://i.imgur.com/uGWBeQB.jpg ...

   Liked On: 06-04-2020, 09:39 AM

2. 
   Steve123 liked post by PaulNZ On thread : Walnut Stock Build

   One more post and this’ll be up to date with where I’m actually at. If I was writing this chronologically, there should actually be a post in between thinking the pattern stock was done and then...

   Liked On: 06-04-2020, 08:47 AM

3. 
   Nickoli liked post by PaulNZ On thread : Walnut Stock Build

   One more post and this’ll be up to date with where I’m actually at. If I was writing this chronologically, there should actually be a post in between thinking the pattern stock was done and then...

   Liked On: 06-04-2020, 08:43 AM

4. 
   madjon_ liked post by PaulNZ On thread : Walnut Stock Build

   So some of the changes I made to the stock at this point were to reduce LOP by ¼”, flatten off the palm swell slightly, and deepen and extend the comb fluting. All easily done. But I also couldn’t...

   Liked On: 06-04-2020, 08:26 AM

5. 
   takbok liked post by PaulNZ On thread : Walnut Stock Build

   Another few snapshots from the milling for your interest. Note that these are all with the wood still wet – the colour did change considerably after drying. https://i.imgur.com/uGWBeQB.jpg ...

   Liked On: 06-04-2020, 08:01 AM

6. 
   ROKTOY liked post by PaulNZ On thread : Walnut Stock Build

   One more post and this’ll be up to date with where I’m actually at. If I was writing this chronologically, there should actually be a post in between thinking the pattern stock was done and then...

   Liked On: 05-04-2020, 10:31 PM

7. 
   R93 liked post by PaulNZ On thread : Walnut Stock Build

   One more post and this’ll be up to date with where I’m actually at. If I was writing this chronologically, there should actually be a post in between thinking the pattern stock was done and then...

   Liked On: 05-04-2020, 10:04 PM

8. 
   SixtyTen liked post by PaulNZ On thread : Walnut Stock Build

   One more post and this’ll be up to date with where I’m actually at. If I was writing this chronologically, there should actually be a post in between thinking the pattern stock was done and then...

   Liked On: 05-04-2020, 09:56 PM

9. 
   nevereadyfreddy liked post by PaulNZ On thread : Walnut Stock Build

   So some of the changes I made to the stock at this point were to reduce LOP by ¼”, flatten off the palm swell slightly, and deepen and extend the comb fluting. All easily done. But I also couldn’t...

   Liked On: 05-04-2020, 07:53 PM

10. 
    Bill999 liked post by PaulNZ On thread : Walnut Stock Build

    I wasn’t going to make this thread until I was a bit further along, however perhaps with the current lockdown now’s a good time. I know I appreciate reading similar threads created by other members –...

    Liked On: 05-04-2020, 08:28 AM

11. 
    nevereadyfreddy liked post by PaulNZ On thread : Walnut Stock Build

    Another few snapshots from the milling for your interest. Note that these are all with the wood still wet – the colour did change considerably after drying. https://i.imgur.com/uGWBeQB.jpg ...

    Liked On: 04-04-2020, 08:11 PM

12. 
    SixtyTen liked post by PaulNZ On thread : Walnut Stock Build

    Another few snapshots from the milling for your interest. Note that these are all with the wood still wet – the colour did change considerably after drying. https://i.imgur.com/uGWBeQB.jpg ...

    Liked On: 04-04-2020, 05:50 PM

13. 
    Klhari liked post by PaulNZ On thread : Tinting epoxy

    I think spraypaint might be risky, but worth a test at least. One stockmaker recommended lampblack (candle soot) as a good bedding pigment. Seems to be plenty of guidance on google on gathering it...

    Liked On: 04-04-2020, 10:33 AM

14. 
    akaroa1 liked post by PaulNZ On thread : Walnut Stock Build

    Yep, at least as far as possible. I spent a whole afternoon on the millers yard with his waterblaster and a crowbar getting as much solidified dirt and stones out of the root ball as possible. We...

    Liked On: 04-04-2020, 10:27 AM

15. 
    Steve123 liked post by PaulNZ On thread : Tinting epoxy

    I think spraypaint might be risky, but worth a test at least. One stockmaker recommended lampblack (candle soot) as a good bedding pigment. Seems to be plenty of guidance on google on gathering it...

    Liked On: 04-04-2020, 10:23 AM

Page 22 of 27 First ... 89101112131415161718192021222324252627 Last

• Jump to page: