PERRISCICABA
Member

3749 Likes

Page 117 of 250 First ... 1767103104105106107108109110111112113114115116117118119120121122123124125126127128129130131167217 ... Last

• Jump to page:

1. 
   PERRISCICABA liked post by chalkeye On thread : Another annealing machine

   I think I need a bit more heating grunt? Will know for sure once this bloody motor controller shows up. https://www.youtube.com/watch?v=qjJbuDKuqFY

   Liked On: 24-05-2016, 08:35 AM

2. 
   PERRISCICABA liked post by chalkeye On thread : Another annealing machine

   https://www.youtube.com/watch?v=CQL0cOdqZMY

   Liked On: 24-05-2016, 08:34 AM

3. 
   PERRISCICABA liked post by greghud On thread : MSC just sacked all its volunteers.

   just back from the road show with the head of the mountain safety council. long story short we will all be replaced by paid staff, delivering to less than a third of the current locations. Yay! i...

   Liked On: 24-05-2016, 08:27 AM

4. 
   PERRISCICABA liked post by mikee On thread : Nelson Steel Gong challenge

   I need more than practice, divine intervention would be a great start in my case

   Liked On: 24-05-2016, 08:26 AM

5. 
   PERRISCICABA liked post by Dundee On thread : Photos your proud of -not just hunting

   Coming up the drive this morning Sylvester greeted me.:D 49794

   Liked On: 22-05-2016, 04:20 PM

6. 
   PERRISCICABA liked post by Gibo On thread : New set of binos

   OK upon researching I believe I was wrong........seems due to using two eyes you will almost always see better than one :D Gadget you are the boss!!

   Liked On: 20-05-2016, 08:15 PM

7. 
   PERRISCICABA liked post by Tombi On thread : Photos your proud of -not just hunting

   49666 Bumped into this little fella this morning

   Liked On: 19-05-2016, 01:10 PM

8. 
   PERRISCICABA liked post by Kscott On thread : Progressive presses, what's the best value.

   Mate is selling his 650 with 9mmm and 223 feeders, etc. Just needs 223 dies apparently. 49633 More than happy with my Dillon. 650 new is @$1400 from Serious for 9mm, plus you'd need 223 bits on...

   Liked On: 18-05-2016, 11:17 PM

9. 
   PERRISCICABA liked post by Timmay On thread : T2 Terminator Muzzle Break mini review

   Kiwi Greg, thanks again, I can't get over how much of a pussy cat this thing is to shoot now. After sighting in at the range with the new Zeiss I headed to the inlaws - they have a pest problem I...

   Liked On: 18-05-2016, 11:14 PM

10. 
    PERRISCICABA liked post by Double Shot On thread : Gun Porn, show off your new toys

    Well a little rifle buy turned into more than I bargained... but with a little work it has turned into a ripper... Bought this Ruger 77/22 WMR as a SS/Laminate, unfortunately the barel wasn't...

    Liked On: 17-05-2016, 08:24 PM

11. 
    PERRISCICABA liked post by 260rem On thread : Tikka T3 Reloading help

    With Andrem Being new to reloading i would not suggest this untill he has some experiance with reloading just go to mag length and work from there try 1mm to 2mm under mag length for a start

    Liked On: 15-05-2016, 09:30 PM

12. 
    PERRISCICABA liked post by ChrisF On thread : Sorting 22lr

    When I heard alot of silhouette shooters use it as practice ammo , I started buying it , and yes my experience is its very good for the dollar , at around 3.99 to 4.59 per box of 50rds , its at a...

    Liked On: 14-05-2016, 10:53 PM

13. 
    PERRISCICABA liked post by Driverman On thread : Sorting 22lr

    Try testing CCI std . I think you will be very surprised

    Liked On: 14-05-2016, 10:49 PM

14. 
    PERRISCICABA liked post by ChrisF On thread : Do Not mix powders

    The link works for me , just scroll down the page ,

    Liked On: 14-05-2016, 10:44 PM

15. 
    PERRISCICABA liked post by Friwi On thread : Tikka T3 Reloading help

    Before you cut anything, load some rounds longer so the bullet is close to the rifling, and test them by feeding your rifle single shot. If results on target are promising then you can do the surgery.

    Liked On: 14-05-2016, 10:35 PM

Page 117 of 250 First ... 1767103104105106107108109110111112113114115116117118119120121122123124125126127128129130131167217 ... Last

• Jump to page: