I'm on my 6th Shilen. They've all shot really well. As do Bartlein, Krieger, Brux, TrueFlite etc... can't go wrong with any of them. My current 284 is a 25.5" Shilen. Chucks 180's out at 2850 with...
Liked On: 30-07-2023, 07:04 PM
I'm on my 6th Shilen. They've all shot really well. As do Bartlein, Krieger, Brux, TrueFlite etc... can't go wrong with any of them. My current 284 is a 25.5" Shilen. Chucks 180's out at 2850 with...
Liked On: 30-07-2023, 02:54 PM
I'm on my 6th Shilen. They've all shot really well. As do Bartlein, Krieger, Brux, TrueFlite etc... can't go wrong with any of them. My current 284 is a 25.5" Shilen. Chucks 180's out at 2850 with...
Liked On: 30-07-2023, 02:15 PM
I'm on my 6th Shilen. They've all shot really well. As do Bartlein, Krieger, Brux, TrueFlite etc... can't go wrong with any of them. My current 284 is a 25.5" Shilen. Chucks 180's out at 2850 with...
Liked On: 30-07-2023, 01:58 PM
"Low power" rifle loads are probably still gonna be higher pressure than hot pistol loads. 308 Winchester is a 60,000 psi cartridge. 45 ACP (which uses LPP's) is 19,000 psi. 44 Magnum (which uses...
Liked On: 10-07-2023, 09:53 PM
"Low power" rifle loads are probably still gonna be higher pressure than hot pistol loads. 308 Winchester is a 60,000 psi cartridge. 45 ACP (which uses LPP's) is 19,000 psi. 44 Magnum (which uses...
Liked On: 10-07-2023, 09:12 PM
My guess... pedestrian. 2217 is even slower burning than CFE, which was already too slow for the 90gr bullets you tried last time... And now you've got a lighter bullet?? As your bullet gets...
Liked On: 08-07-2023, 06:31 AM
You might find your velocity drops a bit by going from an LRM to a LR, with such a large amount of slow powder. One way to find out. Test it. Then you can adjust accordingly.
Liked On: 05-07-2023, 06:21 PM
Yes. So long as you're slow and careful. The firing pin pinches the impact sensitive explosive (aka primer compound) between the cup and the anvil to set it off. A decapping pin will just do the...
Liked On: 05-07-2023, 02:30 AM
Yes. So long as you're slow and careful. The firing pin pinches the impact sensitive explosive (aka primer compound) between the cup and the anvil to set it off. A decapping pin will just do the...
Liked On: 04-07-2023, 10:35 PM
Give the die a little bit of float using an o-ring. The Lee lock rings are good for this. Give the bushing a little bit of float by not screwing the plug down on top of it hard. Anneal and neck turn...
Liked On: 03-07-2023, 10:24 PM
2219 for anything 50 grains or under. BM2 or 8208 for anything up to 60 grains. 8208 or 2206H for up to 77 grains. 2208 for anything heavier. Plenty of deer have been shot with plain 55gr...
Liked On: 23-06-2023, 05:57 PM
With high pressure air tanks, there is a different standard in the US vs Europe too. Can't remember which way around it is... Either it's the US testing bottles to a higher pressure (like 50% over...
Liked On: 23-06-2023, 05:22 PM
If you wring the piss out of a PRC to the same degree with a double based powder analogous to how Re26 works in the smaller Creedmoor case (maybe Re33???), I dare say you'll still see the same...
Liked On: 22-06-2023, 08:40 PM
2219 for anything 50 grains or under. BM2 or 8208 for anything up to 60 grains. 8208 or 2206H for up to 77 grains. 2208 for anything heavier. Plenty of deer have been shot with plain 55gr...
Liked On: 22-06-2023, 08:09 PM