Pommy
Member

1379 Likes

Page 7 of 92 First 12345678910111213141516171819202157 ... Last

• Jump to page:

1. 
   Micky Duck liked post by Pommy On thread : 6mm 95gr in 1:8 twist

   No issue with stability. 1:8's will stabilise 105-108gr boat tails. Shorter, lighter 85-95gr bullets will be fine. Accuracy... This is the same as shooting 55gr from 1:8 twist 223's. 69/77gr is...

   Liked On: 15-11-2024, 04:04 PM

2. 
   Dama dama liked post by Pommy On thread : 6mm 95gr in 1:8 twist

   No issue with stability. 1:8's will stabilise 105-108gr boat tails. Shorter, lighter 85-95gr bullets will be fine. Accuracy... This is the same as shooting 55gr from 1:8 twist 223's. 69/77gr is...

   Liked On: 14-11-2024, 03:05 PM

3. 
   Subsonic liked post by Pommy On thread : Sub sonic

   Pretty much. You are limited on velocity so have to make up for it with mass and frontal area to get the terminal effect. And you only need a tiny bit of powder to send a bullet out at 1000fps so if...

   Liked On: 11-11-2024, 08:34 PM

4. 
   Jhon liked post by Pommy On thread : Best .223 rounds for an 18.5" 1:9 barrel

   Nothing special about the twist rate, length, or it being a CZ that changes much. You will be limited to about 70gr in projectile weight by the twist. 69gr TMK's were what I used to squeeze the...

   Liked On: 11-11-2024, 08:31 AM

5. 
   ZQLewis liked post by Pommy On thread : Sub sonic

   Bigger is better for the bullet. Smaller is better for the case.

   Liked On: 31-10-2024, 06:42 PM

6. 
   Porch-Rocker liked post by Pommy On thread : Best .223 rounds for an 18.5" 1:9 barrel

   Nothing special about the twist rate, length, or it being a CZ that changes much. You will be limited to about 70gr in projectile weight by the twist. 69gr TMK's were what I used to squeeze the...

   Liked On: 31-10-2024, 05:02 PM

7. 
   Micky Duck liked post by Pommy On thread : The x55 and barrel length

   There's no rules*. Shorten it as much as you'd like. You're just gonna lose an increasing amount of velocity for every inch you take off. Probably ~20-40fps for the first few. So keep enough...

   Liked On: 12-10-2024, 04:22 AM

8. 
   TimC liked post by Pommy On thread : ATEC Suppressor experience, problems, and troubleshooting thread

   Optima50 module... 259494 (One very dirty) MegaH2 module... 259495 Got the tools for doing up the A-Locks properly here.

   Liked On: 11-10-2024, 11:32 PM

9. 
   TimC liked post by Pommy On thread : ATEC Suppressor experience, problems, and troubleshooting thread

   JoshB, the difference between the 40, 45, and 50 is diameter (and therefore volume). For a 300wsm I'd suggest the Optima50 or the H3. Feel free to PM me. Bagheera, yes you need the brake end cap...

   Liked On: 11-10-2024, 11:31 PM

10. 
    Beetroot liked post by Pommy On thread : 2206h for 223

    It's far from the only powder that will work. Keep an eye out for BM2 and 8208 too. 2207, 2219, and 2208 are plenty good with the right bullet weights too.

    Liked On: 10-10-2024, 08:38 PM

11. 
    Seventenths liked post by Pommy On thread : 2206h for 223

    It's far from the only powder that will work. Keep an eye out for BM2 and 8208 too. 2207, 2219, and 2208 are plenty good with the right bullet weights too.

    Liked On: 09-10-2024, 10:08 PM

12. 
    Tentman liked post by Pommy On thread : 2206h for 223

    It's far from the only powder that will work. Keep an eye out for BM2 and 8208 too. 2207, 2219, and 2208 are plenty good with the right bullet weights too.

    Liked On: 09-10-2024, 09:02 PM

13. 
    Rock river arms hunter liked post by Pommy On thread : I imported a sigsauer Sierra6bdx scope . I have a story about importing

    And now thoughts and prayers if there is ever a warranty issue with your scope.

    Liked On: 09-10-2024, 03:47 AM

14. 
    dannyb liked post by Pommy On thread : ATEC Suppressor experience, problems, and troubleshooting thread

    JoshB, the difference between the 40, 45, and 50 is diameter (and therefore volume). For a 300wsm I'd suggest the Optima50 or the H3. Feel free to PM me. Bagheera, yes you need the brake end cap...

    Liked On: 08-10-2024, 05:40 PM

15. 
    Bol Tackshin liked post by Pommy On thread : I imported a sigsauer Sierra6bdx scope . I have a story about importing

    And now thoughts and prayers if there is ever a warranty issue with your scope.

    Liked On: 05-10-2024, 09:37 AM

Page 7 of 92 First 12345678910111213141516171819202157 ... Last

• Jump to page: