r87mm
Member

214 Likes

Page 8 of 15 First 123456789101112131415 Last

• Jump to page:

1. 
   7mmwsm liked post by r87mm On thread : A good calibre on pigs

   You have a center fire. The 12 gauge. Solids good to 100+ a bit more. Semi option and no boar shield will stop those ounce loads. If you can line up 3 or 4 pigs it will go through them all. No 223...

   Liked On: 02-06-2020, 08:38 AM

2. 
   rewa liked post by r87mm On thread : Cratered Primer

   Maybe .3-.5 gn over but I'd inspect a few then fire them and re inspect. Could be from load development or near max and the odd one with .1-.2 more than others. As for the craters that is the same...

   Liked On: 08-04-2020, 10:25 PM

3. 
   takbok liked post by r87mm On thread : Cratered Primer

   Maybe .3-.5 gn over but I'd inspect a few then fire them and re inspect. Could be from load development or near max and the odd one with .1-.2 more than others. As for the craters that is the same...

   Liked On: 08-04-2020, 06:24 PM

4. 
   Savage1 liked post by r87mm On thread : Transporter Bellied

   Leave digger where it is. It's to small to be of help. Usually when trying to get off on those angles with a drop off digger ends up down the bank upside down with a hurt operator of stuck half way...

   Liked On: 02-03-2020, 10:04 AM

5. 
   stingray liked post by r87mm On thread : Transporter Bellied

   Leave digger where it is. It's to small to be of help. Usually when trying to get off on those angles with a drop off digger ends up down the bank upside down with a hurt operator of stuck half way...

   Liked On: 27-02-2020, 10:05 PM

6. 
   Jaco Goosen liked post by r87mm On thread : 22 Sako issue

   Sounds like something is a little worn and a gunsmith job. Before it goes that way I'd just check by cleaning the bolt thoroughly with brake clean and trying it incase it's a bit gummed up inside. If...

   Liked On: 13-02-2020, 12:07 PM

7. 
   dannyb liked post by r87mm On thread : 22 Sako issue

   Sounds like something is a little worn and a gunsmith job. Before it goes that way I'd just check by cleaning the bolt thoroughly with brake clean and trying it incase it's a bit gummed up inside. If...

   Liked On: 13-02-2020, 10:58 AM

8. 
   Grimus liked post by r87mm On thread : 7mm RM rechambering

   Talk to Kiwi Greg. As above 180 eld or berger 180. 7mag 2900-3000ish give or take. Your barrel twist is boarder line and will show at distance more than close. Just because it's stable at 1000...

   Liked On: 13-01-2020, 07:13 PM

9. 
   rossi.45 liked post by r87mm On thread : 7mm RM rechambering

   Talk to Kiwi Greg. As above 180 eld or berger 180. 7mag 2900-3000ish give or take. Your barrel twist is boarder line and will show at distance more than close. Just because it's stable at 1000...

   Liked On: 13-01-2020, 07:06 PM

10. 
    Mathias liked post by r87mm On thread : Mathias/wilberforce

    Over seas owner isn't the problem.He believes in keeping access for people. Knew someone who worked there until recently. Managers wife is apparently a piece of work. High staff turn over and even...

    Liked On: 14-12-2019, 05:33 PM

11. 
    Strummer liked post by r87mm On thread : Mathias/wilberforce

    Over seas owner isn't the problem.He believes in keeping access for people. Knew someone who worked there until recently. Managers wife is apparently a piece of work. High staff turn over and even...

    Liked On: 14-12-2019, 02:32 PM

12. 
    ChrisW liked post by r87mm On thread : 7mm mag and 180gr ELDM

    I've got some 7rem brass somewhere and some 180eld's and should have my load specs. I'll throw a dummy one together and give you a coal when I get home The powder did rattle so I knew I had plenty...

    Liked On: 27-08-2019, 06:20 PM

13. 
    ChrisW liked post by r87mm On thread : 7mm mag and 180gr ELDM

    Don't have coal. I load using a comparator so i was 10 thou off the lands based on ogive. It was in a blaser which have a long mag and action as they accommodate bigger cartridges. 30 inch barrel...

    Liked On: 27-08-2019, 05:03 PM

14. 
    ChrisW liked post by r87mm On thread : 7mm mag and 180gr ELDM

    I had 2850fps from a 7mm rem mag. I didn't try for more speed but feel I was getting close. 2225,215fed, norma cases. Rifle had a long mag so could seat out with no compression. Was floating around...

    Liked On: 27-08-2019, 02:33 PM

15. 
    dannyb liked post by r87mm On thread : Muzzle Breaks

    You can as long as there's enough meat in the barrel to be able to thread it to the one that's in the break. Watch out for larger threads like 5/8x24 and bigger if you have a light contour barrel

    Liked On: 26-08-2019, 09:49 AM

Page 8 of 15 First 123456789101112131415 Last

• Jump to page: