Rated M for Magnum
Member

427 Likes

Page 1 of 29 123456789101112131415 ... Last

• Jump to page:

1. 
   Rated M for Magnum liked post by Dicko On thread : Cleaning Rods

   I run a .22 cal rod for rifles below .308 cal and a .308 for above. Incl 9.3. Dewey, proshot are also very good. Polished stainless rods. Specialty rods for .17 rem and the 12 gauge also. ...

   Liked On: 28-02-2025, 11:42 AM

2. 
   Rated M for Magnum liked post by 300CALMAN On thread : Bullet Choice on Hares

   17hmr for head and neck shots out to 120m or so because hare is tasty.

   Liked On: 20-01-2025, 01:36 PM

3. 
   Rated M for Magnum liked post by Mnementh On thread : Securing a pistol safe, wooden house vs concrete floor garage

   Good luck . It will be a nice simple solution that can be used if arms officer is happy 😃 . Thanks for the update

   Liked On: 12-01-2025, 10:06 PM

4. 
   Rated M for Magnum liked post by 199p On thread : Dakota calibres

   Didn't they have some quirk like very short necks?

   Liked On: 04-01-2025, 08:34 PM

5. 
   Rated M for Magnum liked post by Mnementh On thread : Securing a pistol safe, wooden house vs concrete floor garage

   I did something similar .as well as the plate I held it up with 200*200 piles I cut to length I think about 860 or thereabouts on the inside of the joists as well . Being old native timber they were...

   Liked On: 02-01-2025, 10:30 PM

6. 
   Rated M for Magnum liked post by Happy Jack On thread : New 7mm offering by federal

   FUSM Federal Ultra Short Magnum

   Liked On: 30-12-2024, 10:54 AM

7. 
   Rated M for Magnum liked post by Tokoroa Cast Projectiles On thread : .243 subsonic loads

   In some rifles, but not as subsonic loads, they go unstable under 2800fps

   Liked On: 27-12-2024, 04:20 PM

8. 
   Rated M for Magnum liked post by Wanna_eat_meat On thread : Securing a pistol safe, wooden house vs concrete floor garage

   I fabricated a plate for a friend to go under his floor, what i did was measured between the joists, cut a 6mm plate to fit between them, welded a length of 6mm flat on each side to bolt through into...

   Liked On: 25-12-2024, 06:16 PM

9. 
   Rated M for Magnum liked post by caberslash On thread : 7mm mag to a 6.5prc?

   Reloading speeds are equivalent to talking about appendage size. Everyone is up for a boast until an accurate measuring device comes out. Hornady have said that some people claim 6.5 CM loads that...

   Liked On: 06-12-2024, 08:12 AM

10. 
    Rated M for Magnum liked post by mikee On thread : Maker Mucking About

    oh the Makers shed their petals at least the 168gn ones do in a 300WSM, I've not shot the Hammers.

    Liked On: 03-12-2024, 10:56 PM

11. 
    Rated M for Magnum liked post by 308 On thread : Securing a pistol safe

    Heavy channel is C-shaped in section so it can be narrow enough that it is harder to nose an angle grinder in there from below - this is assuming that the c-shape is pointing down so that it looks...

    Liked On: 01-12-2024, 03:51 PM

12. 
    Rated M for Magnum liked post by Tim Dicko On thread : 7mm mag to a 6.5prc?

    300wsm is no slouch, the 208 is a deer slayer, as well as the 215. The 7mm rem mag is my go to , I have a 30nosler. And a 260. I figure a 6.5 prc @2900 with a 147 would work in a 20inch.

    Liked On: 30-11-2024, 11:04 PM

13. 
    Rated M for Magnum liked post by Friwi On thread : Securing a pistol safe

    Do you own the dwelling or do you rent? And how permanently do you want it installed ? The best thing would be to built up a concrete base or concrete box below the floor of the cupboard where you...

    Liked On: 30-11-2024, 10:44 PM

14. 
    Rated M for Magnum liked post by Micky Duck On thread : Info needed .455 Webley

    go for it....there are cast projectiles available off trademe...trailboss is around...its better he collect old guns than young silly sheilahs with hungry ovaries ...much cheaper in long run.

    Liked On: 28-11-2024, 09:14 AM

15. 
    Rated M for Magnum liked post by Kelton On thread : Pruning tools

    Can you confirm it worked with the Lyman holders? Get she’ll holders isn’t out of the question for me as the unit seems sturdy I have the rcbs universal it’s junk the primer tray flys out everytime...

    Liked On: 26-11-2024, 08:19 AM

Page 1 of 29 123456789101112131415 ... Last

• Jump to page: