Roarless20
Member

1158 Likes

Page 46 of 78 First ... 3233343536373839404142434445464748495051525354555657585960 ... Last

• Jump to page:

1. 
   Roarless20 liked post by Kimber 7mm-08 On thread : Rifle bedding - is this normal?

   I'd like to get it back to near where I had it shooting. 200yds230938 200yds230939 200yds230936 440yds230940 3 shot 440yd gong230937

   Liked On: 14-08-2023, 09:23 AM

2. 
   Roarless20 liked post by Jaco Goosen On thread : Rifle bedding - is this normal?

   You cleaned it up real neatly. Good job. Im really interested in seeing how this gun groups. Would have been great if you could have tested it with good hand loads. What kind of accuracy are...

   Liked On: 14-08-2023, 09:22 AM

3. 
   Roarless20 liked post by 6.5 CRD On thread : Lapua 6.5 PRC Brass - Split Necks

   Mine definitely isnt a headspace issue, ive been bumping the shoulder back a thou. Basically all of my lapua brass is wrecked now, slowly but surely the ones that were ok are now buggered. All i can...

   Liked On: 10-08-2023, 01:55 PM

4. 
   Roarless20 liked post by 16Tontovarish On thread : Whats the longest shot youll confidently take at an animal

   If I can get a good prone position and the wind is ok I can confidently get a deer out to 400m. I target shoot further than that but ethically that's as far as I'll go on a live animal. From...

   Liked On: 10-08-2023, 10:36 AM

5. 
   Roarless20 liked post by johnd On thread : Hornady vs Nosler vs Norma brass.

   Personally I think Norma isn't all its cracked up to be. It's really soft and I don't think it takes high pressure well. It's probably very consistent in thickness etc but I stand by my original...

   Liked On: 09-08-2023, 08:09 PM

6. 
   Roarless20 liked post by STC On thread : friends asking how much for load development

   1k??? including 50 rounds and 4 range visits? and after thst 1$ per round? jesus youre cheap! calculate the time you will have to spend. and your hourly rate. including allowance to get to range...

   Liked On: 07-08-2023, 11:26 AM

7. 
   Roarless20 liked post by stug On thread : friends asking how much for load development

   Sections 22D and 22E of the arms act state what needs to be done to supply/sell ammunition. You just need a firearms licence not a dealers.

   Liked On: 07-08-2023, 11:26 AM

8. 
   Roarless20 liked post by TimC On thread : Rifle bedding - is this normal?

   The logic of the guys saying "as long as it shoots better then job done" so you'd be happy if you sent your car in for a wheel alignment, they dented a panel but you'd still be happy as long as the...

   Liked On: 06-08-2023, 09:09 PM

9. 
   Roarless20 liked post by Proudkiwi On thread : Rifle bedding - is this normal?

   It’s a bigger problem now though for the OP than just a rubbish looking bedding job. He was trying to address issues relating to accuracy and rightly decided to try bedding. Now, in my opinion, he...

   Liked On: 05-08-2023, 12:39 PM

10. 
    Roarless20 liked post by Pommy On thread : Rifle bedding - is this normal?

    Looks pretty mediocre to me. It shouldn't be difficult for someone who knows what they're doing to be able to get a much cleaner surface finish. Something was rushed. Either the action was pulled...

    Liked On: 05-08-2023, 12:38 PM

11. 
    Roarless20 liked post by Kelton On thread : Hunting rifle

    I agree with most of the above but if a tikka is within the budget id never recommend otherwise

    Liked On: 03-08-2023, 10:52 PM

12. 
    Roarless20 liked post by Micky Duck On thread : Hunting rifle

    nope....not going to happen UNTIL you have learnt to shoot accurately and consistantly...unless you can guarantee to pop that foot ball at a given range,you have no place to be attempting to shoot an...

    Liked On: 03-08-2023, 10:40 PM

13. 
    Roarless20 liked post by caberslash On thread : Model 7 mag length question

    Few points: M7's are designed around a 2.8" COAL, and use standard Remington 700 S/A magazine boxes and springs (the only part which is compatible between models). Your .223 can be lengthened...

    Liked On: 03-08-2023, 02:26 PM

14. 
    Roarless20 liked post by tnankie On thread : bullet and case comparators

    Hi everyone, heading down the rabbit hole of reloading and I've got the impression knowing your CBTO and headspace/caselength is important. I've been looking about and it seems there are a few of...

    Liked On: 02-08-2023, 06:40 PM

15. 
    Roarless20 liked post by Seventenths On thread : Reloading Poser

    I got caught out like this years ago with an old 7x57 that lost accuracy… I thought it was my reloads but it ended up being loose rings but it wasn’t so obvious until I tightened them up.

    Liked On: 02-08-2023, 02:43 PM

Page 46 of 78 First ... 3233343536373839404142434445464748495051525354555657585960 ... Last

• Jump to page: