Roarless20
Member

1158 Likes

Page 68 of 78 First ... 1854555657585960616263646566676869707172737475767778 Last

• Jump to page:

1. 
   Roarless20 liked post by FRST On thread : Another stock project -M98 25/06

   188367

   Liked On: 12-02-2022, 01:21 PM

2. 
   Roarless20 liked post by T.FOYE On thread : Reloading conundrum - time constraint.

   If it were me, i would set 5 rounds at .05" off the lands (or more). All this '.01" off the lands' is commonly used for VLD's for long range shooting (IMO) but it appears to stem from the BR crowd. I...

   Liked On: 12-02-2022, 10:30 AM

3. 
   Roarless20 liked post by PadLo On thread : What will the hunting rifles of the future look like ?

   189392

   Liked On: 06-02-2022, 01:05 PM

4. 
   Roarless20 liked post by Tahr On thread : Targex ammo

   69grn Targex head shot at 311 yards this evening. 178784

   Liked On: 03-02-2022, 05:43 PM

5. 
   Roarless20 liked post by gundoc On thread : Suppressor thread question

   Take it back to the guy who cut the thread, along with suppressor you intend to use. It is a simple job to repair, 15 minutes tops!

   Liked On: 01-02-2022, 10:08 PM

6. 
   Roarless20 liked post by Shearer On thread : Is it possible to turn a mobile phone into a GPS?

   I use my phone for navigation all the time now. It seems very reliable and you can get better/cheaper maps than a traditional GPS. Topo50, satellite, aerials and plenty of useful overlays. I seldom...

   Liked On: 31-01-2022, 10:30 PM

7. 
   Roarless20 liked post by Sarvo On thread : Best over seas place to buy boots

   Varuste.net

   Liked On: 31-01-2022, 10:20 PM

8. 
   Roarless20 liked post by Micky Duck On thread : Full Length or Neck sizing. What is better and why?

   we all reinvent the wheel..my nosler manual #2 tells how to partial length resize....bump size..... long n short,when base touches instead of screwing in a turn you back out a turn....try it for fit...

   Liked On: 27-01-2022, 07:27 PM

9. 
   Roarless20 liked post by norsk On thread : not enough elevation in scope

   You could hammer a felling wedge in under the Barrel,jack that Barrel up a bit. Just use a polymer one not a steel wedge so you don't scratch the bluing.

   Liked On: 25-01-2022, 10:09 PM

10. 
    Roarless20 liked post by Tahr On thread : 7mm08 Speer 130 and 760

    I used magnum primers with W760 in my loads. Nick Harvey said to :)

    Liked On: 24-01-2022, 11:56 AM

11. 
    Roarless20 liked post by tikka On thread : First fallow and red stag

    No not really, just the first for this year so far. But on this resent trip the first time I’ve seen a falcon catch a bird in flight only 3m or 4m above us and the first time I’ve shot deer and a pig...

    Liked On: 22-01-2022, 07:50 PM

12. 
    Roarless20 liked post by zimmer On thread : 6.5 Grendel load trouble shoot

    I'm a Mitutoyo man myself which comes about from my trade background. The Hornady will most likely be a Chinaman. I also have a Chinese digital calliper and it works perfectly OK. It's the one I...

    Liked On: 22-01-2022, 12:14 PM

13. 
    Roarless20 liked post by hebe On thread : The Ruahines - You get out what you put in

    Haven’t put up any posts etc for a while so thought I’d talk about the last few trips I’ve done this summer in the Ruahines. The first trip was an overnight volunteer trip into the Northern...

    Liked On: 20-01-2022, 09:51 PM

14. 
    Roarless20 liked post by 7mmsaum On thread : Annealing brass

    Try new or annealed brass first to see if your looking in the right direction Then check for carbon ring

    Liked On: 17-01-2022, 08:26 PM

15. 
    Roarless20 liked post by Ftx325 On thread : New Tikka .308 zeroing issues

    THIS as MD mentions ... I cannot shoot my lightweight carbon 338 lap off the bipod on anything resembling a hard surface or the rifle jumps all over the place like a flea on steroids . Even just...

    Liked On: 15-01-2022, 01:55 PM

Page 68 of 78 First ... 1854555657585960616263646566676869707172737475767778 Last

• Jump to page: