Roarless20
Member

664 Likes

Page 1 of 45 123456789101112131415 ... Last

• Jump to page:

1. 
   BSA270 liked post by Roarless20 On thread : 7mm rem magnum accuracy issue

   Check to make sure there is not pitting at the muzzle crown. Very common these days from leaving a suppressor on (even for just a multi day hunt if wet conditions)

   Liked On: 23-03-2025, 09:23 PM

2. 
   dannyb liked post by Roarless20 On thread : 7mm rem magnum accuracy issue

   Check to make sure there is not pitting at the muzzle crown. Very common these days from leaving a suppressor on (even for just a multi day hunt if wet conditions)

   Liked On: 23-03-2025, 08:56 PM

3. 
   charliehorse liked post by Roarless20 On thread : Testing a conventional approach to load development

   Hunterdave Get ready for the "Statistics only" crowd to get rev'd up again :omg: ;)

   Liked On: 14-03-2025, 10:57 AM

4. 
   Bagheera liked post by Roarless20 On thread : The new cartridge that makes the most sense to me.

   The creedmoor case is more effective in a medium action limited to 2.8" coal. More optimal seating position for the projectiles in the case. Less case taper allowing good case capacity for the...

   Liked On: 09-03-2025, 08:44 PM

5. 
   FRST liked post by Roarless20 On thread : Kimber 84m 6mmCM & 7mm08 - hacking up barrels to fit.

   First blood for the kimber with the 6cm barrel. Kaimanawa redstag @ 120ish meters and a young sika stag @ 320m. 268632 268633 The dog resting with his pack loaded with meat. 268634

   Liked On: 24-02-2025, 08:34 PM

6. 
   Tahr liked post by Roarless20 On thread : Maker Mucking About

   Thats a bugger you've got some duds too. Let them (supplier) know also, that way they dont think it was just my one off few. I'm sure Maker will sort them out with replacement stock.

   Liked On: 24-02-2025, 06:52 PM

7. 
   Tahr liked post by Roarless20 On thread : Maker Mucking About

   I have spoken with supplier and will return them so they an see the problem and they will refund me. Tahr of 50 prep'd cases all done the same at same time. Amp annealed and sized, 40 got 75gr...

   Liked On: 24-02-2025, 03:22 PM

8. 
   takbok liked post by Roarless20 On thread : Maker Mucking About

   Well I tried loading some 62gr up for my 223. Turns out i must have a dud batch. A bunch of them have a rough finish and when seated in the case are loose and will spin easily in the neck, but they...

   Liked On: 23-02-2025, 09:11 PM

9. 
   Nick.m liked post by Roarless20 On thread : Kimber 84m 6mmCM & 7mm08 - hacking up barrels to fit.

   First blood for the kimber with the 6cm barrel. Kaimanawa redstag @ 120ish meters and a young sika stag @ 320m. 268632 268633 The dog resting with his pack loaded with meat. 268634

   Liked On: 22-02-2025, 09:05 AM

10. 
    Tim liked post by Roarless20 On thread : Kimber 84m 6mmCM & 7mm08 - hacking up barrels to fit.

    First blood for the kimber with the 6cm barrel. Kaimanawa redstag @ 120ish meters and a young sika stag @ 320m. 268632 268633 The dog resting with his pack loaded with meat. 268634

    Liked On: 21-02-2025, 11:17 AM

11. 
    Tim liked post by Roarless20 On thread : Kimber 84m 6mmCM & 7mm08 - hacking up barrels to fit.

    Time for the 6mm creedmoor barrel to go on... Tikka barrel in the lathe. 266054 Barrel chop from 24" to 18.75", crowned and m14x1 threading. 266055 I made a bushing to go between the...

    Liked On: 21-02-2025, 11:16 AM

12. 
    Rocco liked post by Roarless20 On thread : It's called a carbine, not a bush pig.

    "Bush pig" rolls off the tongue better than "scoped, suppressed carbine"

    Liked On: 20-02-2025, 10:08 PM

13. 
    Deanohit liked post by Roarless20 On thread : Kimber 84m 6mmCM & 7mm08 - hacking up barrels to fit.

    First blood for the kimber with the 6cm barrel. Kaimanawa redstag @ 120ish meters and a young sika stag @ 320m. 268632 268633 The dog resting with his pack loaded with meat. 268634

    Liked On: 20-02-2025, 09:20 PM

14. 
    Deanohit liked post by Roarless20 On thread : Kimber 84m 6mmCM & 7mm08 - hacking up barrels to fit.

    Time for the 6mm creedmoor barrel to go on... Tikka barrel in the lathe. 266054 Barrel chop from 24" to 18.75", crowned and m14x1 threading. 266055 I made a bushing to go between the...

    Liked On: 20-02-2025, 09:18 PM

15. 
    Deanohit liked post by Roarless20 On thread : Kimber 84m 6mmCM & 7mm08 - hacking up barrels to fit.

    I recently purchased a second hand Kimber 84m with the intention of fitting my tikka 6 creedmoor barrel to fit it. Luckily because i bought 'as good' but it was a .308 16" barrel that was poked in...

    Liked On: 20-02-2025, 09:17 PM

Page 1 of 45 123456789101112131415 ... Last

• Jump to page: