Ross Nolan
Member

859 Likes

Page 10 of 58 First 123456789101112131415161718192021222324 ... Last

• Jump to page:

1. 
   Ross Nolan liked post by Percy Jones On thread : Incline / decline shooting

   pythagoras theorem does have its uses.

   Liked On: 19-02-2024, 07:58 AM

2. 
   Ross Nolan liked post by Hokistag On thread : Incline / decline shooting

   Yer it makes sense now- not a position i have been in before so wasnt schooled on how to deal with it but simple science i guess and good learning curve

   Liked On: 14-02-2024, 09:54 PM

3. 
   Ross Nolan liked post by Von Gruff Knives On thread : A Lee Speed stock

   The butt plate being hollow needs careful sculping to get the fit right into the hollow. Quite a bit of time/patience later it is a nice fit. I like to file the waste wood away from the butt plate...

   Liked On: 13-02-2024, 02:05 PM

4. 
   Ross Nolan liked post by Von Gruff Knives On thread : A Lee Speed stock

   With that done it is now that the shaping lines are drawn in and for the bottom line I mark round the top of the trigger guard. https://i.imgur.com/rg4YT8Hl.jpg Next I mark in the forestock...

   Liked On: 13-02-2024, 02:03 PM

5. 
   Ross Nolan liked post by Von Gruff Knives On thread : A Lee Speed stock

   Time now to do the forend tip so a piece of buffalo horn had the face trued up on the grinder belt and cut to length https://i.imgur.com/1x2NFiyl.jpg This piece is barely big enough but with...

   Liked On: 13-02-2024, 02:03 PM

6. 
   Ross Nolan liked post by Von Gruff Knives On thread : A Lee Speed stock

   This morning saw the trigger guard settled into place and then the magazine cut off plate was also fitted with the appropriate wood removed to allow it to operate. Slow and methodical with a great...

   Liked On: 13-02-2024, 02:02 PM

7. 
   Ross Nolan liked post by Von Gruff Knives On thread : A Lee Speed stock

   With the B/A tight into the inlet the unit can be turned over in the vise and the TG sat in between the fixing ears and lined up with the center mark on the underside of the fore stock and fine...

   Liked On: 13-02-2024, 02:02 PM

8. 
   Ross Nolan liked post by Von Gruff Knives On thread : A Lee Speed stock

   First thing toady I drilled 3 10mm holes as a start for the trigger /mag spring assembly and a couple of 20mm and one 24mm holes for the start of the mag well. https://i.imgur.com/yt3DMiVl.jpg ...

   Liked On: 13-02-2024, 02:02 PM

9. 
   Ross Nolan liked post by Gkp On thread : Is the new 7mm PRC a lemon ?

   All barrels shoot different speeds. Hopefully as the cartridge gains traction other companies with enter the market with better quality ammo. For the reloader the 7mm saum does the same thing with...

   Liked On: 13-02-2024, 07:04 AM

10. 
    Ross Nolan liked post by Longrun On thread : Carrying firearm on doc track

    they're

    Liked On: 09-02-2024, 10:08 PM

11. 
    Ross Nolan liked post by timattalon On thread : Carrying firearm on doc track

    Apparently not just the south island....I think the word is actually "They're" as in "They say they are from the North Island?" Mind you even I get caught out sometimes ....English can be a proper...

    Liked On: 09-02-2024, 04:46 PM

12. 
    Ross Nolan liked post by gimp On thread : Groups settling after cleaning

    Sounds like you need to stop cleaning

    Liked On: 04-02-2024, 09:12 AM

13. 
    Ross Nolan liked post by Pommy On thread : Hunting Rifle

    The issue isn't with Mauser/derivatives or controlled feed actions (I own a CZ. And I use it a lot. It's great). The issue is with saying that it's the preferred option, because of a...

    Liked On: 26-01-2024, 08:23 AM

14. 
    Ross Nolan liked post by silentscope On thread : Photos of your dog

    242399 The pigs have the dog bailed

    Liked On: 26-01-2024, 08:21 AM

15. 
    Ross Nolan liked post by Ground Control On thread : Tikka 6x45 / 6mm-223

    I'm not working today due to work being suspended because of the Cyclone happening here in Australia . Perfect timing because my old T3 .223 Tikka is back from Trentech ( Gunsmith ) with a new 6x45...

    Liked On: 25-01-2024, 09:09 PM

Page 10 of 58 First 123456789101112131415161718192021222324 ... Last

• Jump to page: